Poulan 545186804 instruction manual Important Points to Remember, Starting a Warm Engine

Page 10

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15″ -- 18″ (40 -- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope. Starter Rope Handle

Left Hand on Front Handle

Right Foot Through Rear Handle

WARNING: Do not attempt to throw or drop--start the chain saw. Doing so will put the operator at risk of serious injury due to loss of control of the chain saw.

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not attempt to cut material with the choke/fast idle lever in the FULL CHOKE position.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

IGNITION

SWITCH

ON

STOP

Choke

Lever

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.Pull choke/fast idle lever out to the full extent (to the FULL CHOKE position).

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

CHOKE/FAST IDLE LEVER

OFF

HALF

FULL

6.Pull the starter rope sharply with your right hand until the engine starts.

7.Allow the engine to run for approximate- ly 30 seconds. Then, squeeze and re- lease the throttle trigger to allow engine to return to idle speed.

STARTING A WARM ENGINE

1.Move ON/STOP switch to the ON posi- tion.

2.Slowly press primer bulb 6 times.

3.To set the fast idle, pull the choke/fast idle lever out to the full extent (to the full choke position); then push the lever back in to the HALF CHOKE position.

4.Pull the starter rope sharply with your right hand until the engine starts.

5.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine)

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by pushing the choke/fast idle lever in com- pletely (to the OFF CHOKE position) and then following the warm engine starting pro- cedure listed above. Ensure the ON/STOP switch is in the ON position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Plan Ahead Starting ReminderTions found in this manual Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Primer Bulb Throttle LOCK-OUTCHOKE/FAST Idle Lever Chain BrakeDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support Use a wedge to remove pinched sawPruning ServiceLimbing General RecommendationsCheck for Loose Fasteners and Parts Inspect and Clean Unit and DecalsClean AIR Filter Check Chain SharpnessInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenChain Adjustment Replace Spark PlugCooling System Carburetor AdjustmentIdle Speed-T RightFuel System StorageSeasonal Storage EngineTroubleshooting Table Cause Remedy Load Adjustment EnginePoulan Ligations The U.S. EnvironmentalConsequential Damages Poulan

545186804 specifications

The Poulan 545186804 is a powerful and versatile chainsaw that is designed for homeowners and professionals alike. With its robust construction and advanced features, it delivers outstanding performance for various cutting tasks, from trimming branches to felling small trees.

One of the main features of the Poulan 545186804 is its 50cc 2-cycle engine, which provides ample power for demanding applications. The engine is designed for efficiency and optimal fuel consumption, ensuring that users can complete their tasks without frequent refueling. Coupled with a high-performance 20-inch bar and chain, this chainsaw can handle a range of cutting tasks, making it an ideal choice for both heavy-duty work and casual use.

The Poulan 545186804 also includes several technologies aimed at enhancing user experience and safety. It features an automatic oiler system that ensures consistent lubrication to the chain, reducing wear and prolonging the life of the chainsaw. This system ensures that the bar and chain are properly lubricated during operation, helping to maintain cutting efficiency and prevent overheating.

Safety is a crucial consideration in the design of the Poulan 545186804. The chainsaw is equipped with a chain brake that stops the chain’s rotation in the event of kickback, protecting the user from potential injuries. Additionally, it has a comfortable grip handle that reduces vibration, allowing for extended use without causing fatigue in the hands or arms.

Another notable characteristic of the Poulan 545186804 is its lightweight design. Weighing in at just over 11 pounds, it is easy to maneuver and control, making it suitable for users with varying levels of experience. The chainsaw also features an easy-access air filter and spark plug, simplifying maintenance and ensuring that the unit operates at peak performance.

Overall, the Poulan 545186804 combines power, safety, and user-friendly features, making it an excellent choice for anyone in need of a reliable chainsaw. Whether you are a seasoned professional or a weekend warrior, this chainsaw offers the tools necessary to tackle a variety of cutting tasks efficiently and safely.
Top Page Image Contents