Poulan 545186804 Carburetor Adjustment, Idle Speed-T, Cooling System, Right, Wrong

Page 17

File Holder

File

Depth Gauge Tool

File

Cutter

90˚

Depth Gauge

Depth Gauge

SAlign the 30˚ file holder marks paral- lel with the bar and to the center of the chain.

Cutter

30˚

Cutter

File Holder Line

 

SSharpen cutters on one side of the chain first. File from the inside of each cutter to the outside. Then, turn the chain saw around and repeat the pro-

cess for the other side of the chain.

SFile on the forward stroke only. Use 2 or 3 strokes per cutting edge.

SKeep all cutters the same length

when filing.

SFile enough to remove any damage to cutting edges (side plate and top plate of cutter).

All Cutters

Remove Damage

Same Length

 

 

Top Plate

 

Side Plate

SFile chain to meet the specifications as shown.

85˚60

30˚

Hook Angle

 

 

0.025 inch

 

 

(0.65 mm)

 

 

Rounded

Right

Corner

 

Too Much Hook Angle

 

Squared Off

 

 

Corner

Wrong

 

WARNING:

Maintain the proper

hook angle according to the manufacturer’s specifications for the chain you are using. Im- proper hook angle will increase the chance of kickback which can result in serious injury.

4. Check and lower depth gauges.

SPlace gauge tool on cutter.

SIf the depth gauge is higher than the

depth gauge tool, file it level to the top of the depth gauge tool.

SMaintain rounded front corner of depth gauge with a flat file.

NOTE: The very top of the depth gauge should be flat with the front

half rounded off with a flat file.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T

adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

COOLING SYSTEM

To keep the working temperature as low as possible the machine is equipped with a cooling system.

The cooling system consists of:

SAir intake on the starter S Air guide plate

S Fins on the flywheel

S Cooling fins on the cylinder

S Cylinder cover (directs cold air over the cylinder)

Clean the cooling system with a brush after each use, more often in demanding condi- tions. A dirty or blocked cooling system re- sults in the machine overheating which causes damage to the piston and cylinder.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackMaintain Control Reduce the Chance of KickbackAvoid Pinch-Kickback Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Attaching the BAR & Chain If not AssemblyChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation CHOKE/FAST Idle Lever Throttle LOCK-OUTPrimer Bulb Chain BrakeStarting a Warm Engine Important Points to RememberDifficult Starting or starting a flooded engine Right Foot Through Rear HandleInertia activating function control Braking function control Caution The chain brake must beOperating Tips Tree Felling TechniquesNotch CUT and Felling the Tree Felling Large TreesCutting a Fallen Tree Important PointsBucking Without a Support Bucking Using a LOG or Support StandLimbing and Pruning Important Points Use a wedge to remove pinched sawLimbing ServicePruning General RecommendationsClean AIR Filter Inspect and Clean Unit and DecalsCheck for Loose Fasteners and Parts Check Chain SharpnessChain Adjustment Cleaning the Spark ARREST- ING ScreenInspect Muffler and Spark Arresting Screen Replace Spark PlugIdle Speed-T Carburetor AdjustmentCooling System RightSeasonal Storage StorageFuel System EngineLoad Adjustment Engine Troubleshooting Table Cause RemedyLigations The U.S. Environmental PoulanConsequential Damages Poulan

545186804 specifications

The Poulan 545186804 is a powerful and versatile chainsaw that is designed for homeowners and professionals alike. With its robust construction and advanced features, it delivers outstanding performance for various cutting tasks, from trimming branches to felling small trees.

One of the main features of the Poulan 545186804 is its 50cc 2-cycle engine, which provides ample power for demanding applications. The engine is designed for efficiency and optimal fuel consumption, ensuring that users can complete their tasks without frequent refueling. Coupled with a high-performance 20-inch bar and chain, this chainsaw can handle a range of cutting tasks, making it an ideal choice for both heavy-duty work and casual use.

The Poulan 545186804 also includes several technologies aimed at enhancing user experience and safety. It features an automatic oiler system that ensures consistent lubrication to the chain, reducing wear and prolonging the life of the chainsaw. This system ensures that the bar and chain are properly lubricated during operation, helping to maintain cutting efficiency and prevent overheating.

Safety is a crucial consideration in the design of the Poulan 545186804. The chainsaw is equipped with a chain brake that stops the chain’s rotation in the event of kickback, protecting the user from potential injuries. Additionally, it has a comfortable grip handle that reduces vibration, allowing for extended use without causing fatigue in the hands or arms.

Another notable characteristic of the Poulan 545186804 is its lightweight design. Weighing in at just over 11 pounds, it is easy to maneuver and control, making it suitable for users with varying levels of experience. The chainsaw also features an easy-access air filter and spark plug, simplifying maintenance and ensuring that the unit operates at peak performance.

Overall, the Poulan 545186804 combines power, safety, and user-friendly features, making it an excellent choice for anyone in need of a reliable chainsaw. Whether you are a seasoned professional or a weekend warrior, this chainsaw offers the tools necessary to tackle a variety of cutting tasks efficiently and safely.
Top Page Image Contents