Poulan 545186804 instruction manual Service, Limbing, Pruning, General Recommendations

Page 14

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop-

erly.

SLeave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and limbs. Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

S Remove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and free- ly hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your first cut 1/3 of the way through the

bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 to 5 cm) collar from the truck of the tree.

Second cut

Third cut

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized or Master Service Dealer.

HELPFUL TIP

IMPORTANT: Have all

repairs other than the rec- ommended maintenance described in the instruction manual performed by an authorized service dealer.

If any dealer other than an authorized service dealer performs work on the product, Poulan may not pay for repairs under warranty. It is your responsibility to maintain and perform general mainte- nance.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . . Before each use For damaged parts . . . Before each use For loose caps . . . . . . Before each use For loose fasteners . . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

*Hours of Operation --

Each hour of operation is approximately 2 tanks of fuel.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must main- tain unit as instructed in this manual. Various adjustments will need to be made periodical- ly to properly maintain your unit.

SOnce a year, replace the spark plug, air filter, and check guide bar and chain for wear. A new spark plug and air filter assures proper air-fuel mixture and helps your engine run better and last longer.

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for re- placement of damaged or worn parts.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Manual de Instrucciones Manuel d’Instructions Tions found in this manual Starting ReminderPlan Ahead Handle Fuel with Caution Operate Your SAW SafelyMaintain Your SAW in Good Working Order KickbackAvoid Pinch-Kickback Reduce the Chance of KickbackMaintain Control Avoid Pull-InChain saws as set by Ansi B175.1 Kickback Safety FeaturesChain Brake and CKA Angle Assembly Attaching the BAR & Chain If notChecking the tension Adjusting the tensionChain Tension Know Your Chain SAW ON/STOP Switch Throttle TriggerOperation Primer Bulb Throttle LOCK-OUTCHOKE/FAST Idle Lever Chain BrakeDifficult Starting or starting a flooded engine Important Points to RememberStarting a Warm Engine Right Foot Through Rear HandleOperating Tips Braking function control Caution The chain brake must beInertia activating function control Tree Felling TechniquesCutting a Fallen Tree Felling Large TreesNotch CUT and Felling the Tree Important PointsLimbing and Pruning Important Points Bucking Using a LOG or Support StandBucking Without a Support Use a wedge to remove pinched sawPruning ServiceLimbing General RecommendationsCheck for Loose Fasteners and Parts Inspect and Clean Unit and DecalsClean AIR Filter Check Chain SharpnessInspect Muffler and Spark Arresting Screen Cleaning the Spark ARREST- ING ScreenChain Adjustment Replace Spark PlugCooling System Carburetor AdjustmentIdle Speed-T RightFuel System StorageSeasonal Storage EngineTroubleshooting Table Cause Remedy Load Adjustment EnginePoulan Ligations The U.S. EnvironmentalConsequential Damages Poulan

545186804 specifications

The Poulan 545186804 is a powerful and versatile chainsaw that is designed for homeowners and professionals alike. With its robust construction and advanced features, it delivers outstanding performance for various cutting tasks, from trimming branches to felling small trees.

One of the main features of the Poulan 545186804 is its 50cc 2-cycle engine, which provides ample power for demanding applications. The engine is designed for efficiency and optimal fuel consumption, ensuring that users can complete their tasks without frequent refueling. Coupled with a high-performance 20-inch bar and chain, this chainsaw can handle a range of cutting tasks, making it an ideal choice for both heavy-duty work and casual use.

The Poulan 545186804 also includes several technologies aimed at enhancing user experience and safety. It features an automatic oiler system that ensures consistent lubrication to the chain, reducing wear and prolonging the life of the chainsaw. This system ensures that the bar and chain are properly lubricated during operation, helping to maintain cutting efficiency and prevent overheating.

Safety is a crucial consideration in the design of the Poulan 545186804. The chainsaw is equipped with a chain brake that stops the chain’s rotation in the event of kickback, protecting the user from potential injuries. Additionally, it has a comfortable grip handle that reduces vibration, allowing for extended use without causing fatigue in the hands or arms.

Another notable characteristic of the Poulan 545186804 is its lightweight design. Weighing in at just over 11 pounds, it is easy to maneuver and control, making it suitable for users with varying levels of experience. The chainsaw also features an easy-access air filter and spark plug, simplifying maintenance and ensuring that the unit operates at peak performance.

Overall, the Poulan 545186804 combines power, safety, and user-friendly features, making it an excellent choice for anyone in need of a reliable chainsaw. Whether you are a seasoned professional or a weekend warrior, this chainsaw offers the tools necessary to tackle a variety of cutting tasks efficiently and safely.
Top Page Image Contents