Poulan 545137224 instruction manual Storage

Page 16

6.Reinstall spark arresting screen, exhaust outlet cover, and nut. Tighten nut securely.

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and non- adjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ--7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. Spark plug gap should be 0.025 inch (0,6 mm).

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten securely.

Cylinder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by run- ning it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and re- assemble.

CHAIN ADJUSTMENT

See CHAIN TENSION in ASSEMBLY sec- tion.

CHAIN SHARPENING

Chain sharpening is a complicated task and requires special tools. We recommend that you refer chain sharpening to a professional chain sharpener.

CARBURETOR ADJUSTMENT

WARNING: The chain will be mov- ing during most of this procedure. Wear your protective equipment and observe all safety precautions. The chain must not move at idle speed.

The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SChain moves at idle. See IDLE SPEED--T adjusting procedure.

SSaw will not idle. See IDLE SPEED--T ad- justing procedure.

Idle Speed-T

Allow engine to idle. If the chain moves, idle is too fast. If the engine stalls, idle is too slow. Ad- just speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). The idle speed screw is located in the area above the primer bulb and is labeled T.

STurn idle screw (T) clockwise to increase engine speed.

S Turn idle screw (T) counterclockwise to decrease engine speed.

If you require further assistance or are unsure about performing this procedure, contact your authorized service dealer or call our customer assistance help line at 1--800--554--6723.

STORAGE

WARNING: Perform the following steps after each use:

SAllow the engine to cool, and secure the unit before storing or transporting.

SStore chain saw and fuel in a well venti- lated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore chain saw with all guards in place

and position chain saw so that any sharp object cannot accidentally cause injury.

SStore chain saw well out of the reach of children.

SEASONAL STORAGE

Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more.

If your chain saw is to be stored for a period of time:

SClean saw thoroughly before storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces and guide bar.

SOil the chain and wrap it in heavy paper or cloth.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your chain saw.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum depos- its during storage. Add stabilizer to the gaso- line in the fuel tank or fuel storage container. Follow the mix instructions found on stabiliz- er containers. Run engine at least 5 minutes after adding stabilizer.

Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with fuel stabilizer. If you do not use this oil, you can add a fuel stabilizer to your fuel tank.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions 545137224 11/30/06Plan Ahead Starting ReminderTions found in this manual Operate Your SAW Safely Maintain Your SAW in Good Working OrderHandle Fuel with Caution KickbackReduce the Chance of Kickback Maintain ControlAvoid Pinch-Kickback Avoid Pull-InChain Brake and CKA Angle Kickback Safety FeaturesChain saws as set by Ansi B175.1 Assembly Attaching the BAR & Chain If notChain Tension Adjusting the tensionChecking the tension Operation ON/STOP Switch Throttle TriggerKnow Your Chain SAW Throttle LOCK-OUT Chain Brake CHOKE/FAST Idle LeverPrimer Bulb Before Starting EngineImportant Points to Remember Starting a Warm EngineDifficult Starting or starting a flooded engine Right Foot Through Rear HandleBraking function control Caution The chain brake must be Inertia activating function controlOperating Tips Tree Felling TechniquesFelling Large Trees Notch CUT and Felling the TreeCutting a Fallen Tree Important PointsBucking Using a LOG or Support Stand Bucking Without a SupportLimbing and Pruning Important Points LimbingService Inspect and Clean Unit and Decals Clean AIR FilterCleaning the Spark ARREST- ING Screen Check Fuel Mixture LevelStorage Engine Load Adjustment EngineOther Limited Warranty Ligations The U.S. EnvironmentalNANCE, Replacement and Repair

545137224 specifications

The Poulan 545137224 is a powerful and versatile chainsaw designed for both professional landscapers and homeowners alike. Renowned for its performance and durability, this model embodies a harmonious blend of advanced technology and user-friendly features, making it a top choice for various cutting tasks.

One of the standout features of the Poulan 545137224 is its 50cc engine, which delivers a robust output, allowing users to tackle heavy-duty cutting jobs with ease. The engine's powerful design ensures efficient fuel consumption, which not only enhances performance but also reduces the frequency of refueling. This makes it ideal for extended use in larger yard projects or logging operations.

Equipped with a 20-inch bar and chain, the Poulan 545137224 allows for deep and precise cuts, cutting through thick wood quickly. This longer guide bar increases the cutting capacity, making it suitable for felling trees, limbing, and general wood cutting tasks. The chainsaw's low kickback chain further enhances safety without sacrificing cutting efficiency, ensuring that users can operate it with confidence.

One of the notable technologies incorporated into this chainsaw is the patented Easy Start system. This innovative feature enables easier pull starts, which is particularly beneficial for those who may struggle with traditional recoil starters. The automatic oiler system is another impressive characteristic, ensuring that the chain is continuously lubricated during use, thus extending the lifespan of both the chain and the bar.

In terms of design, the Poulan 545137224 is crafted with user comfort in mind. It features an ergonomic handle that provides a secure and comfortable grip, reducing fatigue during prolonged use. The chainsaw is also relatively lightweight for its power class, allowing for enhanced maneuverability without sacrificing strength.

For maintenance, the Poulan 545137224 includes tool-less chain tightening, simplifying the process of chain adjustments and replacements. This practical design element saves time and makes upkeep more accessible for all users.

Overall, the Poulan 545137224 represents a reliable choice for anyone in need of a high-performance chainsaw. With its powerful engine, advanced technologies, user-friendly design, and maintenance features, this chainsaw stands out as a reliable tool for a variety of cutting tasks in both residential and commercial settings.
Top Page Image Contents