Service, Pruning, Limbing, AIR Filter | Poulan 2004-07, 530165412

Using a support stand

2nd Cut

1st Cut

2nd Cut

PRUNING

WARNING: Limit pruning to limbs shoulder height or below. Do not cut if branches are higher than your shoulder. Get a professional to do the job.

SMake your fist cut 1/3 of the way through the bottom of the limb.

SNext make a 2nd cut all the way through the limb. Then cut a third overcut leaving a 1 to 2 inch (2.5 -- 5 cm) collar from the truck of the tree.

Second cut

Third cut

LIMBING AND PRUNING

WARNING: Be alert for and guard against kickback. Do not allow the moving chain to contact any other branches or ob- jects at the nose of the guide bar when limb- ing or pruning. Allowing such contact can re- sult in serious injury.

WARNING: Never climb into a tree to limb or prune. Do not stand on ladders, platforms, a log, or in any position which can cause you to lose your balance or control of the saw.

IMPORTANT POINTS

S Work slowly, keeping both hands firmly gripped on the saw. Maintain secure foot- ing and balance.

S Watch out for springpoles. Springpoles are small size limbs which can catch the saw chain and whip toward you or pull you off balance. Use extreme caution when cutting small size limbs.

S Be alert for springback. Watch out for branches that are bent or under pressure. Avoid being struck by the branch or the saw when the tension in the wood fibers is released.

SKeep a clear work area. Frequently clear branches out of the way to avoid tripping over them.

LIMBING

SAlways limb a tree after it is cut down. Only then can limbing be done safely and prop- erly.

S Leave the larger limbs underneath the felled tree to support the tree as you work.

SStart at the base of the felled tree and work toward the top, cutting branches and

limbs. Remove small limbs with one cut.

SKeep the tree between you and the chain. Cut from the side of the tree opposite the

branch you are cutting.

SRemove larger, supporting branches with the cutting techniques described in BUCK-

ING WITHOUT A SUPPORT.

SAlways use an overcut to cut small and freely hanging limbs. Undercutting could cause limbs to fall and pinch the saw.

Collar

First cut

Pruning technique

SERVICE

WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments.

We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level . . . . Before each use Bar lubrication . . . . . . . Before each use Chain tension . . . . . . . Before each use Chain sharpness . . . . . Before each use For damaged parts . . . Before each use For loose caps . . . . . . Before each use For loose fasteners . . . Before each use For loose parts . . . . . . Before each use

Inspect and Clean:

Bar . . . . . . . . . . . . . . . . Before each use Complete saw . . . . . . . After each use Air filter . . . . . . . . . . . . . Every 5 hours* Chain brake . . . . . . . . . Every 5 hours* Spark arresting screen

and muffler . . . . . . . . . . Every 25 hours* Replace spark plug . Yearly Replace fuel filter . . . Yearly

*Hours of Operation --

Each hour of operation is approximately 2 tanks of fuel.

AIR FILTER

CAUTION: Do not clean filter in gasoline or other flammable solvent to avoid creating a fire hazard or producing harmful evapora- tive emissions.

2004-07, 530165412 specifications

The Poulan 2004-07,530165412 is a notable model in the Poulan range, which is well-regarded for its reliability and performance in lawn care and outdoor maintenance. Designed primarily for homeowners and light commercial use, this trimmer has garnered attention for its robust features and innovative technologies that enhance both efficiency and user experience.

One of the main features of the Poulan 2004-07,530165412 is its powerful engine. The unit typically boasts a two-stroke engine, which provides sufficient power and torque to tackle various yard maintenance tasks, including trimming grass, weeds, and light brush. The engine's lightweight design makes it easy to maneuver, reducing fatigue during extended use.

Equipped with a straight shaft design, the Poulan trimmer allows users to access difficult-to-reach areas such as under shrubs and fences. The design also helps improve performance and reduces the risk of clogging, enabling a cleaner cut. This model often features a dual-line cutting system that spins at high speed, providing a wider cutting path for faster trimming. The bump feed head allows users to easily advance the cutting line with a simple tap on the ground, ensuring uninterrupted operation.

In terms of ergonomics, the Poulan 2004-07,530165412 incorporates adjustable handles to cater to users of various heights. The padded grips enhance comfort during prolonged use, while the lightweight body reduces strain on the arms and back.

Technologically, this model may include anti-vibration features that minimize feedback to the user, helping to decrease operator fatigue and increase trimming efficiency. The fuel efficiency of the engine is another highlight, allowing users to spend more time working and less time refueling.

Maintenance is straightforward, which is essential for homeowners and semi-professionals alike. The easy-start system simplifies starting, and the accessible air filter and spark plug contribute to a user-friendly maintenance routine.

Overall, the Poulan 2004-07,530165412 is a well-rounded trimmer, blending power, versatility, and user comfort. Its enhancements serve to elevate the user experience, making yard work less of a chore and more efficient. Whether you are tackling a residential lawn or light landscaping projects, this model stands out in the crowded market of outdoor power tools.