Poulan 2004-07, 530165412 instruction manual Checking the tension, Adjusting the tension, Cutters

Page 7

Cutters

Depth Gauge

Drive Links

Place chain onto the sprocket

7.Place chain over and behind clutch, fitting the drive links in the clutch drum sprocket.

8.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

9.Fit chain drive links into bar groove.

10.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

11.Now, install chain brake making sure the adjusting pin is positioned in the lower hole in the guide bar. Remember this pin moves the bar forward and backward as the screw is turned.

12.Install chain brake nuts and finger tighten only. Once the chain is tensioned, you will need to tighten chain brake nuts.

CHAIN TENSION (Including units with chain already installed)

NOTE: When adjusting chain tension, make sure the chain brake nuts are finger tight only. Attempting to tension the chain when the chain brake nuts are tight can cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust- ment tool (bar tool) to move the chain around the bar. If the chain does not rotate, it is too tight. If too loose, the chain will sag below the bar.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain stretches during use. This is especially true during the first few times you use your saw. Always check chain tension each time you use and refuel your saw.

You can adjust the chain tension by loosen- ing the chain brake nuts and turning the ad- justing screw 1/4 of a turn while lifting up on the bar.

SIf chain is too tight, turn adjusting screw 1/4 turn counterclockwise.

SIf chain is too loose, turn adjusting screw 1/4 turn clockwise.

Adjusting

Screw

Chain Brake Nuts

Guide Bar

Adjusting Screw -- 1/4 Turn

SLift up the tip of the bar and securely tight-

en the chain brake nuts with the bar tool.

SRecheck chain tension.

Chain Brake

Nuts

WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsSafety Rules Identification of SymbolsPlan Ahead Kickback Operate Your SAW SafelyMaintain Your SAW in Good Working Order Handle Fuel with CautionAvoid Obstructions Clear The Working Area Kickback Safety FeaturesReduce the Chance of Kickback Maintain Control952044418 18″ Chain Brake and CKA AngleComputed kickback angle CKA Table LengthAlready attached AssemblyInside view Chain Brake Adjustment located on Chain Brake Attaching the BAR & Chain If notCutters Adjusting the tensionChain Tension Including units with chain already installed Checking the tensionThrottle Lockout ON/STOP SwitchKnow Your SAW Throttle TriggerImportant Points to Remember StartingFueling Engine BAR and Chain LubricationStarting a Warm Engine Cutting MethodsImportant Points Felling Large Trees Tree Felling TechniquesNotch CUT and Felling the Tree Bucking Without a Support Bucking Using a LOG or Support StandCutting a Fallen Tree Types of Cutting Used for BuckingLimbing ServicePruning Limbing and Pruning Important PointsInspect Muffler and Spark Arresting Screen Cleaning the air filterCarburetor Adjustment BAR MaintenanceNeed ASSISTANCE? Load Adjustment Engine Limited WarrantyEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Ligations The U. S. EnvironmentalIntermediate 125 hours Extended 300 hours

2004-07, 530165412 specifications

The Poulan 2004-07,530165412 is a notable model in the Poulan range, which is well-regarded for its reliability and performance in lawn care and outdoor maintenance. Designed primarily for homeowners and light commercial use, this trimmer has garnered attention for its robust features and innovative technologies that enhance both efficiency and user experience.

One of the main features of the Poulan 2004-07,530165412 is its powerful engine. The unit typically boasts a two-stroke engine, which provides sufficient power and torque to tackle various yard maintenance tasks, including trimming grass, weeds, and light brush. The engine's lightweight design makes it easy to maneuver, reducing fatigue during extended use.

Equipped with a straight shaft design, the Poulan trimmer allows users to access difficult-to-reach areas such as under shrubs and fences. The design also helps improve performance and reduces the risk of clogging, enabling a cleaner cut. This model often features a dual-line cutting system that spins at high speed, providing a wider cutting path for faster trimming. The bump feed head allows users to easily advance the cutting line with a simple tap on the ground, ensuring uninterrupted operation.

In terms of ergonomics, the Poulan 2004-07,530165412 incorporates adjustable handles to cater to users of various heights. The padded grips enhance comfort during prolonged use, while the lightweight body reduces strain on the arms and back.

Technologically, this model may include anti-vibration features that minimize feedback to the user, helping to decrease operator fatigue and increase trimming efficiency. The fuel efficiency of the engine is another highlight, allowing users to spend more time working and less time refueling.

Maintenance is straightforward, which is essential for homeowners and semi-professionals alike. The easy-start system simplifies starting, and the accessible air filter and spark plug contribute to a user-friendly maintenance routine.

Overall, the Poulan 2004-07,530165412 is a well-rounded trimmer, blending power, versatility, and user comfort. Its enhancements serve to elevate the user experience, making yard work less of a chore and more efficient. Whether you are tackling a residential lawn or light landscaping projects, this model stands out in the crowded market of outdoor power tools.
Top Page Image Contents