Poulan 2004-07 Starting, Fueling Engine, BAR and Chain Lubrication, Important Points to Remember

Page 9

FUELING & LUBRICATION

WARNING: Remove fuel cap slow- ly when refueling.

FUELING ENGINE

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce container of Poulan/Weed Eater brand synthetic oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive or boat oil. These oils will cause engine damage. When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules listed under HANDLE FUEL WITH CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

Genuine PoulanR bar and chain oil is recommended to protect your unit against excessive wear from heat and friction. PoulanR oil resists high temperature thinning. If PoulanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

STARTING

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15 --- 18 inches (38 --- 45 cm) of rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope rewind slowly.

For cold weather starting, start the unit at FULL CHOKE; allow the engine to warm up before squeezing the throttle trigger.

NOTE: Do not cut material with the choke/ fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or warm engine after running out of fuel):

NOTE: In the following steps, when the choke/fast idle lever is pulled out to the full extent, the correct throttle setting for starting is set automatically.

ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull out choke/fast idle to the full extent (to the FULL CHOKE position).

3.Slowly press primer bulb 6 times.

4.Pull the starter rope sharply 5 times with your right hand. Then, proceed to the next step.

NOTE: If the engine sounds as if it is trying to start before the 5th pull, stop pulling and immediately proceed to the next step.

5.Push the choke/fast idle lever in to the HALF CHOKE position.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsIdentification of Symbols Safety RulesPlan Ahead Maintain Your SAW in Good Working Order Operate Your SAW SafelyHandle Fuel with Caution KickbackReduce the Chance of Kickback Kickback Safety FeaturesMaintain Control Avoid Obstructions Clear The Working AreaComputed kickback angle CKA Table Chain Brake and CKA AngleLength 952044418 18″Inside view Chain Brake Adjustment located on Chain Brake AssemblyAttaching the BAR & Chain If not Already attachedChain Tension Including units with chain already installed Adjusting the tensionChecking the tension CuttersKnow Your SAW ON/STOP SwitchThrottle Trigger Throttle LockoutFueling Engine StartingBAR and Chain Lubrication Important Points to RememberCutting Methods Starting a Warm EngineImportant Points Tree Felling Techniques Felling Large TreesNotch CUT and Felling the Tree Cutting a Fallen Tree Bucking Using a LOG or Support StandTypes of Cutting Used for Bucking Bucking Without a SupportPruning ServiceLimbing and Pruning Important Points LimbingCarburetor Adjustment Cleaning the air filterBAR Maintenance Inspect Muffler and Spark Arresting ScreenNeed ASSISTANCE? Limited Warranty Load Adjustment EngineEmpty fuel tank and refill with Electrolux Home PRODUCTS, INC Ligations The U. S. EnvironmentalIntermediate 125 hours Extended 300 hours

2004-07, 530165412 specifications

The Poulan 2004-07,530165412 is a notable model in the Poulan range, which is well-regarded for its reliability and performance in lawn care and outdoor maintenance. Designed primarily for homeowners and light commercial use, this trimmer has garnered attention for its robust features and innovative technologies that enhance both efficiency and user experience.

One of the main features of the Poulan 2004-07,530165412 is its powerful engine. The unit typically boasts a two-stroke engine, which provides sufficient power and torque to tackle various yard maintenance tasks, including trimming grass, weeds, and light brush. The engine's lightweight design makes it easy to maneuver, reducing fatigue during extended use.

Equipped with a straight shaft design, the Poulan trimmer allows users to access difficult-to-reach areas such as under shrubs and fences. The design also helps improve performance and reduces the risk of clogging, enabling a cleaner cut. This model often features a dual-line cutting system that spins at high speed, providing a wider cutting path for faster trimming. The bump feed head allows users to easily advance the cutting line with a simple tap on the ground, ensuring uninterrupted operation.

In terms of ergonomics, the Poulan 2004-07,530165412 incorporates adjustable handles to cater to users of various heights. The padded grips enhance comfort during prolonged use, while the lightweight body reduces strain on the arms and back.

Technologically, this model may include anti-vibration features that minimize feedback to the user, helping to decrease operator fatigue and increase trimming efficiency. The fuel efficiency of the engine is another highlight, allowing users to spend more time working and less time refueling.

Maintenance is straightforward, which is essential for homeowners and semi-professionals alike. The easy-start system simplifies starting, and the accessible air filter and spark plug contribute to a user-friendly maintenance routine.

Overall, the Poulan 2004-07,530165412 is a well-rounded trimmer, blending power, versatility, and user comfort. Its enhancements serve to elevate the user experience, making yard work less of a chore and more efficient. Whether you are tackling a residential lawn or light landscaping projects, this model stands out in the crowded market of outdoor power tools.
Top Page Image Contents