Oregon S402022H0/S402022K0 owner manual Operation, Towing, Maintenance

Page 17

CAUTION: TURN FUEL SHUT OFF VALVE TO THE “OFF” POSITION PRIOR TO TOWING.FAILURE TO DO SO MAY RESULT IN FLOODING THE ENGINE.

NOTE: The engine maximum governed speed is preset at the factory at 3600 RPM no load speed. When splitting wood the throttle should be set at the maximum speed to develop the horsepower required for the pump.

OPERATION

WARNING: See safety information related to operation of the log splitter in the safety section of this manual. Make sure that you have the

recommended personal protective equipment described on page 1.

1)Set up the log splitter in a clear, level area and block the wheels. Make sure that the suction port on the tank is always on the lower side of the log splitter.

2)For horizontal operation place a log on the beam against the foot plate. Make sure the the log is securely on the foot plate and up against the beam.To split wood in the vertical position, release the pin on the beam latch located near the front end of the beam. Carefully tilt the beam up until the foot plate is sitting squarely on the ground and the log splitter is stable. Place the log on the foot plate up against the beam. When the beam is returned to the horizontal position make sure the beam latch is securely locked down. See illustrations of beam latch in Step 7 on page 9.

3)With the engine running, depress the valve handle so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the end of its stroke. If the log has not completely split after the cylinder has reached the end of its extension, retract the cylinder.

IMPORTANT: Leaving the valve in the “actuate” position at the end of the stroke may damage the pump. Always use extra care when splitting logs with unsquare ends.

NOTE: For operation in wooded areas, obtain a spark arrestor for the exhaust system. See the engine operating and maintenance manual and check with your authorized Honda or Kohler service center. See also Fire Prevention on page 5 of this manual.

IMPORTANT: TO EXTEND THE LIFE OF THE HYDRAULIC CYLINDER, AVOID “BOTTOMING OUT” WEDGE PLATE TO THE FOOT PIECE. TO CONFORM WITH INDUSTRY SAFETY RECOMMENDATIONS, THE WEDGE STOPS 1.5 INCHES FROM THE END OF THE STROKE.

TOWING

This log splitter is equipped with pneumatic tires, a Class I coupler (2 in. diameter ball required) and safety chains. Before towing, the safety chains must be secured to the hitch or bumper of the vehicle. Local regulations should be checked regarding licensing, lights, towing, etc.Turn fuel shut off valve on the engine to the “Off” position prior to towing. Failure to do so may result in flooding the engine. Do not exceed 45 mph when towing this log splitter. See also Towing Safety on page 6 of this manual.

MAINTENANCE

1)Consult the operating and maintenance instructions of the engine manufacturer for engine care and maintenance.

2)Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an adequate oil supply will cause severe damage to the pump.

3)Change the oil filter after the first 25 hours of operation. There after change the oil filter every 100 hours or seasonally, whichever comes first.

4)To drain the hydraulic oil, loosen the clamp on the hose coming from the fitting on the bottom of the tank. It is located just to the right of the oil filter.

5)If the wedge becomes dull or nicked, it can be removed and sharpened. Remove the 1/2 in. diameter bolt that connects the wedge to the cylinder. hose from the valve. The hose from the valve may need to be removed. Carefully lift the cylinder to allow the wedge to slide forward. The wedge can now be lifted off and sharpened.

6)Clean the breather cap after 25 hours of operation. Clean it more often when operated in dusty conditions. To clean, remove the breather cap from the tank and flush with kerosene or liquid detergent to remove the dirt.

7)See also Repair and Maintenance Safety on page 4 of this manual.

8) All replacement parts must meet manufacturer’s specifications.

Page 15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents VERTICAL/HORIZONTAL 22 TON LOG Splitter Table of Contents Personal Protective Equipment Safety DecalsIntended USE Location Hydraulic Tank Lower TANK, Right Corner Preparation of the LOG General SafetyWork Area General Repair Operation of the LOG SplitterFire Prevention Maintenance & SafetyTowing Safety Item no Description QTY Assembly InstructionsItem no Decsription QTY Beam 3/4 R Clip Pin Tank/Tongue Assembly Pivot Pin Item no Descrption QTY Wheel Assembly Breakdown Item NO. Part no Description QTY Replacement PartsItem no Description QTY Beam Assembly BreakdownItem no Description Tongue Assembly BreakdownEngine Operating InstructionsEngine OIL Recommendations Kohler SH265 Towing MaintenanceOperation Log Splitter Accessories Important Notice Warranty Repair and ServiceSpecifications

S402022H0/S402022K0 specifications

Oregon S402022H0 and S402022K0 are two advanced weather stations designed for both hobbyist meteorologists and professionals alike. These models are part of Oregon Scientific’s commitment to providing high-quality, reliable weather monitoring solutions that cater to a wide range of users.

One of the main features of the S402022H0 and S402022K0 is their ability to deliver accurate real-time weather data. Equipped with high-precision sensors, these devices can measure temperature, humidity, atmospheric pressure, wind speed, and rainfall. This comprehensive data collection allows users to gain insights into local weather patterns, essential for planning outdoor activities or managing agricultural practices.

Both models stand out due to their user-friendly interfaces, featuring clear LCD screens that display the weather data in an easily readable format. Additionally, these weather stations often come with wireless capabilities, allowing the sensors to communicate with the main unit without cumbersome wiring. This feature enhances the installation flexibility, as sensors can be placed in optimal locations without concern for running wires back to the display unit.

Another significant technological advancement in the Oregon S402022H0 and S402022K0 is support for connectivity with mobile devices. Users can often sync the data from these weather stations to smartphones or tablets via dedicated apps. This connectivity ensures that users can monitor weather conditions remotely, offering convenience and flexibility, especially for those on the go.

Moreover, these models typically offer robust data logging capabilities. Users can track historical weather data over time, enabling them to analyze trends and make informed decisions based on past weather patterns. This feature is particularly beneficial for researchers and professionals in agriculture, construction, and environmental sciences.

The S402022H0 and S402022K0 weather stations are also designed with durability in mind. Constructed to withstand various environmental conditions, these devices can function reliably in various climates, making them suitable for both indoor and outdoor use.

In summary, the Oregon S402022H0 and S402022K0 weather stations impress with their comprehensive feature set, technological advancements, and reliable performance. They are invaluable tools for anyone looking to enhance their understanding of their local weather conditions while enjoying the convenience of modern technology.
Top Page Image Contents