Rhino Mounts 2408 manual Attaching Pin on Bucket, Mounting Loader

Page 42

ASSEMBLY

ASSEMBLY

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader until hoses will reach from loader to tractor. Engage tractor brakes and shut off tractor engine.

2.Make sure quick couplers are clean and connect between tractor and loader, matching color coded bands.

3.Remove bolts, nuts and washers from hinge.

4.Start tractor engine and release tractor brakes. Slowly drive tractor ahead until front mounting brackets are directly under loader catch flats. Activate lift control lever so that catch flats hook securely on front mounting bracket tubes. Continue driving loader forward while rolling the loader on the front mounting bracket tubes until side frame uprights are fully resting on midmounting assembly. Engage tractor brakes and shut off engine.

5.Hook rubber strap around hoses and back on itself. Attach other end of rubber strap to bolt at front of corner or side frame.

6.Clamp hinge assembly around midmounting tube. Install bolts, washers and nuts. Torque cap screws to 126 Ft. Lbs.

Attaching Pin on Bucket

Always wear safety glasses when removing or installing buckets.

Material bucket can be installed using tool ordinarily available.

1.Attach bucket to lift boom frame and cylinders with four 1” pins, use two 3/8 shoulder bolts and 3/8 lock nuts at upper pin (bucket cylinder). Use two 3/8 x 1.25 hex bolts, 3/8 jam nut, 3/8 flat washer and 3/8 lock nut at lower pin. Position bolt with head on inside of outer bucket ear. Fasten bolt to ear using 3/8 jam nut. Install pin so pin head is over jam nut and retain with 3/8 flat washer and 3/8 lock nut.

2.Install level indicator rod in level guide tube on right bucket cylinder. Sandwich level indicator rod angle between right inside bucket ear and cylinder rod end.

3.Set bucket level on ground and adjust level guide tube along bucket cylinder until end of guide tube is flush with end of rod.

2408 01/11

Assembly Section 3-6

© 2011 Alamo Group Inc.

Page 41 Page 43
Image 42
Page 41 Page 43
Contents 2408 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices2408 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2408 01/11 Safety Section Safety Safety SL-33 Safety Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2408 01/11 Safety Section See Your Rhino Dealer Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 2408 01/11 Safety Section Loader Safety Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Dismounting Loader and Mounting Loader to TractorAssembly Proper Ballasting and Wheel Spacing Dismounting Loader Attaching Pin on Bucket Mounting LoaderAssembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor Requirements Rops and Seat BeltTractor Lighting and SMV Emblem Getting On and Off the Tractor Tractor BallastBoarding the Tractor Dismounting the TractorStarting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection and ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketOperation Lifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Loader Storage Transporting the Tractor and ImplementShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyProblem Possible Cause Remedy Maintenance Section Maintenance 2408 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly Storage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Rhino To the OWNER/OPERATOR/DEALER SOM-01/11 F-3971C Printed U.S.A

2408 specifications

Rhino Mounts 2408 is a cutting-edge mounting solution designed for a variety of applications, catering to the ever-evolving needs of professionals and enthusiasts alike. This innovative product is built to support a range of equipment securely and efficiently, providing stability and versatility in different environments.

One of the main features of the Rhino Mounts 2408 is its robust construction. Made from high-quality aluminum, this mount is both lightweight and exceptionally durable, ensuring it can withstand the rigors of daily use without compromising performance. The corrosion-resistant finish further enhances its longevity, making it suitable for outdoor applications where environmental factors could otherwise lead to wear and tear.

The 2408 model offers impressive adjustability, allowing users to easily customize the mount to their specific needs. With a variety of tilt and rotation options, it can accommodate different viewing angles, ensuring optimal visibility and accessibility. This flexibility is particularly useful in professional settings, where precise alignment can make a significant difference in functionality and efficiency.

Rhino Mounts 2408 features advanced locking mechanisms, ensuring that equipment remains securely in place during operation. These mechanisms are designed to be user-friendly, allowing for quick adjustments without the need for specialized tools. This ease of use makes the mount suitable for a wide range of users, from seasoned professionals to those new to the field.

The mount’s compatibility is another highlight, designed to work seamlessly with a variety of devices and brands. Whether mounting cameras, monitors, or other equipment, the Rhino Mounts 2408 provides a reliable solution that ensures stability and performance. Its universal design and adaptability to various attachments make it an ideal choice for diverse applications.

Additionally, the mount incorporates innovative vibration-dampening technology that enhances stability and minimizes disruptions during operation. This feature is especially beneficial in high-frequency environments, where vibrations can impact the performance of the mounted equipment. By absorbing and reducing vibrations, the 2408 model enhances the overall user experience.

In summary, Rhino Mounts 2408 stands out as a versatile, durable, and adaptable mounting solution. With its robust construction, flexible adjustability, secure locking mechanisms, broad compatibility, and advanced vibration-dampening technology, it offers users a reliable option for mounting needs across various applications. Whether in a studio, on a job site, or in a dynamic field environment, the 2408 model ensures that equipment is securely held and easily accessible, enabling maximum efficiency and effectiveness.
Top Page Image Contents