Scag Power Equipment STT-31BSG manual Custom Cut Baffle

Page 29

Section 6

To adjust the Custom-Cut Baffle height:

1.Place the cutter deck in the transport position.

2.Remove the hardware securing the Custom-Cut Baffle to the cutter deck. (See Figure 6.8).

-NOTE-

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

MOUNTING￿ MOUNTING￿

HARDWAREHARDWARE

2002 CCB

Figure 6-8. Custom Cut Baffle

3.Move the Custom-Cut Baffle to desired position. (See Figures 6.9 through 6.11 for position).

4.Reinstall the mounting hardware as shown. (See Figures 6.10 though 6.11). Torque hardware to 39ft.lbs.

2002 CCB - 3" Setting￿

Figure 6-9. 3" Custom Cut Baffle Position

CARRIAGE BOLT

 

 

2002 CCB - 3-1/2" Setting￿

BOTTOM SET OF HOLES￿

FLATWASHER

ELASTIC STOP￿

FOR 3-1/2" SETTING

 

NUT

Figure 6-10. 3-1/2" Custom Cut Baffle Position

CARRIAGE BOLT

 

 

2002 CCB - 4" Setting￿

TOP SET OF HOLES￿

FLATWASHER

ELASTIC STOP￿

 

NUT

FOR 4" SETTING

 

 

 

Figure 6-11. 4" Custom Cut Baffle Position

25

Image 29
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Before Operation Considerations Safety InformationOperation Considerations Before Operation Considerations ContdOperation Considerations Contd Maintenance ConsiderationsSafety and Instructional Decals Drive System EngineEngine Deck Additional Specifications SpecificationsApproximate Dimensions ProductivityControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking the Mower Recommendations for Mowing Removing Clogged MaterialMoving Mower with Engine Stopped Towing optional hitch accessory Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdTravel Adjustments AdjustmentsParking Brake Adjustment RH Steering Control Rod Adjustment Neutral AdjustmentThrottle Control and Choke Adjustments Tracking AdjustmentBelt Adjustment Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle AdjustmentCustom Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine Fuel System Engine AIR CleanerBattery Battery Electrolyte First AID Charging the BatteryDrive Belts Jump StartingCutter Blades Blade InspectionTires Blade ReplacementChecking Lubricant Level Cutter Deck GearboxCooling System Checking Coolant LevelBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Page 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 48825 48314 481937 Limited Warranty Commercial Equipment 2002
Related manuals
Manual 62 pages 3.37 Kb