Scag Power Equipment STT-31BSG manual Hillside Operation, Parking the Mower, After Operation

Page 18

Section 4

4.Always operate the engine at full throttle to properly maintain cutting speed. If the engine starts to lug down, reduce the forward speed and allow the engine to operate at maximum RPM.

4.7 HILLSIDE OPERATION

WARNING:

DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1.The mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control.

2.To prevent tipping or loss of control, start and stop smoothly, avoid unnecessary turns and travel at reduced speed.

3.Keep tires properly inflated.

4.8 PARKING THE MOWER

1.Place the steering control levers in the neutral position.

2.Disengage the cutter blades

3.Slow the engine to idle speed.

4.Engage the parking brake.

5.Turn the ignition key to the OFF position and remove the key.

4.9 AFTER OPERATION

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

-IMPORTANT-

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment and any signs of wear. Correct and adjust if necessary.

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

4.After the mower has cooled down, fill the fuel tank with fresh, clean fuel at the end of every day of operation.

5.Check the tire pressure. Adjust pressure if necessary.

14

Image 18
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Before Operation ConsiderationsBefore Operation Considerations Contd Operation ConsiderationsMaintenance Considerations Operation Considerations ContdSafety and Instructional Decals Engine Engine DeckDrive System Approximate Dimensions SpecificationsAdditional Specifications ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerAfter Operation Removing Clogged Material Moving Mower with Engine StoppedRecommendations for Mowing Adjusting Cutting Height Towing optional hitch accessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment RH Steering Control Rod AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Checking Engine Crankcase Oil Level Engine OILChanging Hydraulic Oil Filter Element Changing Engine Crankcase OilEngine AIR Cleaner BatteryEngine Fuel System Charging the Battery Battery Electrolyte First AIDCutter Blades Jump StartingDrive Belts Blade InspectionBlade Replacement TiresCooling System Cutter Deck GearboxChecking Lubricant Level Checking Coolant LevelCleaning the Radiator Debris Screen Checking The Fan Belt TensionBODY, DECK, and Upholstery Page 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 48825 48314 481937 Limited Warranty Commercial Equipment 2002
Related manuals
Manual 62 pages 3.37 Kb