DECK DRIVE COMPONENTS
Ref. Part |
| Ref. | Part |
| |
No. | No. | Description | No. | No. | Description |
|
|
|
|
|
|
1 | 422845 | Belt Guard, Rear | 53 | Bolt, Hex Head | |
2 | 481531 | Hinge, Rear Belt Guard | 54 | ||
3 | 481309 | Latch, Hood | 55 | Nut | |
4 | Carr. Bolt | 56 | Nut, Elastic | ||
5 | Nut, Serr. Flg. | 57 | 43504 | Pivot, Idler - Long | |
6 | Screw, | 58 | Bolt, Hex Head | ||
7 | Lock Washer, #10 | 59 | Nut, Elastic | ||
8 | Nut, | 60 | Bolt, Hex Head | ||
9 | 451457 | Weldment, Pump Mounting | 61 | Lock Washer 5/16” | |
10 | 43506 | Spacer, Engine | 62 | 422684 | Brace, Engine Mounting Plate |
11 | 43507 | Stud, | 63 | 481284 | Bumper, Rubber |
12 | 482433 | Linkage Assembly, | 64 | ||
13 | Tie, Cable | 65 | Bolt, Hex Head | ||
14 | Pin, Rue | 66 | Clamp, Wire | ||
15 | Bolt, Hex Head | 67 | Bolt, Carr. | ||
16 | 46977 | Spindle Assembly, Deck Drive | 68 | 482438 | Driveshaft |
17 | 461467 | Clutch, Electric PTO | 69 | 43296 | Spacer, Inside |
18 | 481398 | Pulley, 6.35” dia. Tapered Bore | 70 | 43297 | Bushing |
19 | 481536 | Hub, Tapered 1” dia. | 71 | 481025 | Seal, 2.00 OD x 1.625 Bore |
20 | Key, 1/4 x 1/4 x 1.5” | 72 | 481035 | Nut, | |
21 | Bolt, Hex Head | 73 | 481022 | Roller Bearing Assembly | |
22 | 481883 | Pulley, 6.25” OD, Tapered | 74 | 43312 | Spacer, Outside |
23 | 481788 | Pulley, 5.45” OD | 75 | Grease Fitting | |
24 | Set Screw, | 76 | 48677 | Relief Fitting | |
25 | 481884 | Hub, Tapered 17mm Bore | 77 | 43294 | Spindle Housing |
26 | Bolt, Hex Head | 78 | 481024 | Seal, 2.00 OD x 1.5 Bore | |
27 | Key, 5mm x 5mm x 30mm | 79 | 43534 | Shaft, Spindle | |
28 | 481461 | Belt, Pump Drive | 80 | Screw, Set | |
29 | 481460 | Belt, Deck Drive | 81 | Nut, Center Lock | |
30 | Key, 1/4 x 1/4 x 2.5” | 82 | Bolt, Hex Head | ||
31 | Bolt, Hex Head | 83 | Key, 1/4 x 1/4 x 1” |
32
33
34
35
36
37
38 461079 | Idler Arm |
39
40
4148181 Pulley, PTO Idler
42
43
44481522 Spring
4548224 Bearing
4643503 Pivot, Idler - Short
47
48422714 Base, Idler Pivot
49
50 | 461015 | Idler Arm |
51 | 48198 | Pulley, Pump Idler |
52 | 43277 | Spacer |
* Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated.
45