Scag Power Equipment STT-31BSG manual Charging the Battery, Battery Electrolyte First AID

Page 36

Section 7

WARNING:

Lead-acid batteries produce flammable and explosive gases. To avoid personal injury when checking, testing or charging batteries, DO NOT use smoking materials near batteries. Keep arcs, sparks and flames away from batteries. Provide proper ventilation and wear safety glasses.

WARNING:

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after han- dling.

1.Loosen the two plastic wing nuts and then remove the battery cover.

2.Remove the battery cell caps. Visually inspect electrolyte level in the cells. If electrolyte is below the bottom of vent well, fill with clean distilled water to the bottom of vent wells (1/4 to 1/2 inch above the plates). Install the battery cell caps.

-IMPORTANT-

Do not overfill the battery. Electrolyte will over- flow through the vent tube onto parts of the machine, resulting in severe corrosion.

3.Clean the cable ends and battery posts with steel wool. Use a solution of baking soda and water to clean the battery. Do not allow the solution to enter the battery cells.

4.Tighten the cable connections securely and apply a light coat of silicone dielectric grease to the terminal connections to prevent corrosion.

5.Install the battery cover.

WARNING:

Electric storage battery fluid contains sulfuric acid which is POISON and can cause SEVERE CHEMICAL BURNS. Avoid contact of fluid with eyes, skin, or clothing. Use proper protective gear when handling batteries. DO NOT tip any battery beyond 45° angle in any direction. If fluid contact does occur, follow first aid suggestions below.

BATTERY ELECTROLYTE FIRST AID

EXTERNAL CONTACT — Flush with water.

EYES — Flush with water for at least 15 minutes and get medical attention immediately.

INTERNAL — Drink large quantities of water. Follow with Milk Of Magnesia, beaten egg, or vegetable oil. Get medical attention immediately. In case of internal contact, DO NOT give fluids that would induce vomiting.

B. Charging the Battery

Refer to the battery charger’s manual for specific instructions.

Under normal conditions the engine’s alternator will have no problem keeping a charge on the battery. If the battery has been completely discharged for a long period of time, the alternator may not be able to recharge the battery, and a battery charger will be required.

DO NOT charge a frozen battery. It may explode and cause injury. Let the battery warm before attaching a charger.

Whenever possible, remove the battery from the mower before charging and make sure the electrolyte covers the plates in all cells.

32

Image 36
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd General Information IntroductionDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Safety Information Before Operation ConsiderationsBefore Operation Considerations Contd Operation ConsiderationsMaintenance Considerations Operation Considerations ContdSafety and Instructional Decals Engine Engine DeckDrive System Specifications Additional SpecificationsApproximate Dimensions ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Parking the MowerAfter Operation Removing Clogged Material Moving Mower with Engine StoppedRecommendations for Mowing Adjusting Cutting Height Towing optional hitch accessoryTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment RH Steering Control Rod AdjustmentTracking Adjustment Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Adjustments Cutter Deck LevelCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom Cut Baffle Maintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Engine OIL Changing Hydraulic Oil Filter ElementChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine AIR Cleaner BatteryEngine Fuel System Charging the Battery Battery Electrolyte First AIDJump Starting Drive BeltsCutter Blades Blade InspectionBlade Replacement TiresCutter Deck Gearbox Checking Lubricant LevelCooling System Checking Coolant LevelCleaning the Radiator Debris Screen Checking The Fan Belt TensionBODY, DECK, and Upholstery Page 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 48825 48314 481937 Limited Warranty Commercial Equipment 2002
Related manuals
Manual 62 pages 3.37 Kb