Scag Power Equipment STT-31BSG manual Engine Fuel System, Engine AIR Cleaner, Battery

Page 35

Section 7

7.5 ENGINE FUEL SYSTEM

2. Install a new fuel filter. Be sure it is installed in the

 

proper direction. Secure to the fuel hose using the

 

two clamps.

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

Fuel Filter￿

(with hose clamps￿ above and below)

STT99FF-1

Figure 7-5 Fuel Filter

A. Filling the Fuel Tank

Fill the fuel tank at the beginning of each operating day to within 1 inch below the filler neck. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87.

B. Replacing In-Line Fuel Filter Element

-NOTE-

The fuel filter is located below the hydraulic tank. Figure 7-5 is for illustration purposes only.

The in-line fuel filter (Figure 7-5) should be replaced after every 500 hours of operation or annually, whichever occurs first.

1.Close the shut-off valve. Remove the two clamps securing the fuel filter to the fuel hose. Remove the fuel filter.

7.6 ENGINE AIR CLEANER

A. Cleaning and/or Replacing Air Cleaner Element

For any air cleaner, the operating environment dictates the air cleaner service periods. To make it convenient for you we have installed an "Air Cleaner Indicator" which is located just behind the air filter. The indicator window will turn red when it is time to service the air filter. Do not service the filter unless this indicator is red.

-NOTE-

In extremely dusty conditions it may be necessary to check the indicator daily to prevent engine damage.

1.Snap open the two clips securing the air cleaner cover to the air cleaner box. Remove the air cleaner cover, clean the duck bill vent of any dust and set the cover aside.

2.Remove the air cleaner element and inspect.

3.Clean or replace the element as recommended by the engine manufacturer.

4.Replace the air filter cover and be sure to snap closed the two clips.

5.Reset the air cleaner indicator by pushing the button on the end of the indicator. The indicator window should return to clear.

7.7 BATTERY

A. Checking Electrolyte Level and Cleaning Battery

After every 40 hours of operation or weekly, whichever occurs first, check the electrolyte level in the battery and clean the battery and connections. Dirt and fluid on the top of the battery can cause the battery to discharge. Corrosion of the battery terminals or loose connections will cause poor battery performance.

31

Image 35
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Before Operation Considerations Safety InformationOperation Considerations Before Operation Considerations ContdOperation Considerations Contd Maintenance ConsiderationsSafety and Instructional Decals Drive System EngineEngine Deck Productivity SpecificationsAdditional Specifications Approximate DimensionsControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking the Mower Recommendations for Mowing Removing Clogged MaterialMoving Mower with Engine Stopped Towing optional hitch accessory Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdTravel Adjustments AdjustmentsParking Brake Adjustment RH Steering Control Rod Adjustment Neutral AdjustmentBelt Alignment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle AdjustmentCustom Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Engine Crankcase Oil Engine OILChanging Hydraulic Oil Filter Element Checking Engine Crankcase Oil LevelEngine Fuel System Engine AIR CleanerBattery Battery Electrolyte First AID Charging the BatteryBlade Inspection Jump StartingDrive Belts Cutter BladesTires Blade ReplacementChecking Coolant Level Cutter Deck GearboxChecking Lubricant Level Cooling SystemBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension Page 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Wheel Assy Inc.items 20, 42, 43, 54 Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Part Description Fuel and Hydraulic System Ref. Part Description Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 48825 48314 481937 Limited Warranty Commercial Equipment 2002
Related manuals
Manual 62 pages 3.37 Kb