Scag Power Equipment STC52V-24FX, STC61V-27CV, STC48V-22FS-LE Seat Belt Inspection

Page 11

Section 2

R

WARNING

Failure to properly inspect and maintain the seat belt can cause serious injury or loss of life.

1.Check the full length of the seat belt webbing for cuts, wear, fraying, dirt and stiffness. See Figure 2-3.

2.Check the seat belt webbing in areas exposed to ultra violet rays from the sun or extreme dust or dirt. If the original color of the webbing in these areas is extremely faded and/or is packed with dirt, the physical strength of this webbing may have deteriorated. If this condition exists, replace the seat belt system.

3.Check the buckle and latch for proper operation and determine if the latch plate is excessively worn, deformed, or if the buckle is damaged or cracked. See Figure 2-3.

INSPECT BUCkLE

& LATCH

INSPECT WEBBING

Figure 2-3. Seat Belt Inspection

7

20o

15o

10o

5o

Figure 2-4. Slope Angle Graph

WARNING

Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.

Stay off of slopes too steep for safe operation. To check a slope, attempt to back up it (with the cutter deck down). If the machine can not back up the slope without the wheels slipping, do not operate the machine on this slope. Under no circumstances should the machine be operated on slopes greater than 15 degrees. See Figure 2-4 to determine approximate slope.

DO NOT mow near drop-offs, ditches or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge caves in.

Operate the machine smoothly, no sudden turns, starts or stops on a slope.

NEVER tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.

DO NOT permit untrained personnel to operate the machine.

Be cautious when loading and unloading onto trailers or trucks.

Use only a full width ramp.

Ramp angle should be no more than 15 Degrees. See Figure 2-4 to help determine approximate slope.

Back up the ramp and drive down forward.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents OPERATOR’S Manual STC48V-22FS-LE Remember Your Mower is only AS Safe AS the OperatorTable of Contents Following Section Limited Warranty Commercial EquipmentServicing The Engine and Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsBefore Operation considerations Safety InformationSignal Words Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection SPARK Ignition System Maintenance Considerations & storageUsing a spark arrestor Install Belt COvER Before Safety and Instructional DecalsTractor SpecificationsEngine ElectricalProductivity Weights and Dimensions 48V 52V 61VCutter Deck Hydraulic SystemControls and Instrument Identification Operating InstructionsInitial RUN-IN Procedures Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Reverse Travel Engaging the Deck Drive Cutter BladesAfter Operation Rotating BladesHillside Operation Parking the MowerRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Deck Release Lever Towing optional hitch accessoryCondition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Travel Adjustments AdjustmentsParking Brake Adjustment Tracking Adjustment Neutral AdjustmentBelt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Adjustment ROD Lock NUTPosition Custom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelSection Engine AIR Cleaner Jump Starting BatteryCharging the Battery Blade Inspection Blade ReplacementDrive Belts Cutter BladesBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts List48V & 52V Cutter Decks Description 61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 423912 Bracket, Fuel Valve STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat 483386 Seat Assembly Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Steering Components Brake Components Brake Components Hydraulic System Available through the individual engine manufacturer Engine STC Fuel System EPA Phase STC Fuel System EPA Phase 3 models produced after 1/1/2011 Models produced after 1/1/2011 STC Fuel System EPA PhaseSTC Fuel System C.A.R.B. Tier STC Fuel System C.A.R.B. Tier Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Heavy-Duty Replacement Decals and Information Plates482166R STC 2009 RDP2 PTO Switch Diode KEY Electrical Schematic Briggs & Stratton / KohlerPlug Electrical Schematic KawasakiLimited Warranty Commercial Equipment

STC48V-22FS, STC52V-24FX, STC48V-22FS-LE, STC61V-27CV specifications

Scag Power Equipment has a longstanding reputation for producing high-quality zero-turn mowers, and the models STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS stand out for their exceptional performance, durability, and innovative technologies.

The STC61V-27CV is equipped with a robust 27 HP Kohler engine, providing ample power for cutting through tough grass and elevating efficiency in landscaping tasks. Its 61-inch Velocity Plus cutting deck ensures a superior mowing experience, delivering precise cuts with the ability to handle various turf conditions. This model features a comfortable seat and ergonomic controls, ensuring maximum operator comfort during extended use. Additionally, the cutting height can be easily adjusted from 1 to 5 inches, allowing users to customize their mowing to suit different grass types and preferences.

Meanwhile, the STC48V-22FS-LE boasts a compact design ideal for residential and commercial properties. Powered by a 22 HP Kawasaki engine, this model is equipped with a 48-inch cutting deck, which offers a perfect balance between maneuverability and cutting capacity. The LE package includes luxurious features such as a high-back seat for added comfort and easy access to maintenance points, ensuring that the mower remains in peak condition. The model's easy-to-use controls and responsive steering make it an excellent choice for first-time users.

The STC52V-24FX offers a blend of power and versatility with its 24 HP Kawasaki engine and 52-inch cutting deck. This model is designed for those who require a longer run-time and increased productivity. The mower features an innovative grass catcher option, making it easier to collect clippings for a tidy finish. Furthermore, the heavy-duty frame enhances structural integrity, while the commercial-grade components ensure long-lasting service.

Lastly, the STC48V-22FS enhances user experience with its practical features. Similar to other models, it features a 22 HP Kawasaki engine coupled with a 48-inch cutting deck, tailored for residential lawns and smaller commercial properties. The mower’s compact design and efficient grass discharge system optimize cutting performance while minimizing downtime.

Overall, Scag Power Equipment offers a wide range of high-performance zero-turn mowers. Each model, including the STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS, incorporates advanced technologies and superior engineering to meet the demands of any lawn care professional or dedicated homeowner. With a commitment to innovation and quality, Scag continues to set the standard for excellence in outdoor power equipment.
Top Page Image Contents