Scag Power Equipment STC61V-27CV, STC48V-22FS-LE, STC52V-24FX Engine AIR Cleaner

Page 37

Section 7

R

FILLER NECK

INSERT

FUEL LEVEL

10.Replace gas cap and tighten securely. For Low Emission (LE) and EPA Phase 3 (produced after 1/1/2011) models, tighten the fuel cap until it ratchets.

B. REPLACING IN-LINE FUEL FILTER ELEMENTS

The engine fuel filter should be replaced after every 500 hours of operation or annually, whichever occurs first.

1.Close the shut-off valve.

2.Remove and replace the engine fuel filter. Open the fuel shut-off valve.

7.6 ENGINE AIR CLEANER

A. CLEANING AND/OR REPLACING AIR CLEANER ELEMENT

Figure 7-6. C.A.R.B. / EPA Phase 3 Fuel Level

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

1.Extinguish all cigarettes, cigars, pipes and other sources of ignition.

2.Use only an approved gasoline container.

3.Never remove the gas cap or add fuel with the engine running. Allow the engine to completely cool before fueling.

4.Never fuel the machine indoors or in an enclosed trailer.

5.Never store the machine or fuel container where there is an open flame, spark or pilot light such as on a water heater or other appliances.

6.Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground away from your vehicle before filling.

7.Remove the machine from the truck or trailer and fuel on the ground. If this is not possible, then refuel the machine with a portable container, rather than from a gasoline dispenser nozzle.

8.Keep the nozzle in contact with the rim of fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

9.If fuel is spilled on clothing, change clothing immediately and wash affected skin.

For any air cleaner, the operating environment dictates the air cleaner service periods. Inspect and clean the air cleaner element after every 100 hours of operation or bi- weekly, whichever occurs first and replace the element if required.

- NOTE -

In extremely dusty conditions it may be necessary to check the element once or twice daily to prevent engine damage.

1.Release the two latches securing the air cleaner cover to the air cleaner assembly and remove the cover. Set aside.

2.Remove the air cleaner and inspect.

3.Clean or replace the air cleaner and foam pre-cleaner as recommended by the engine manufacturer.

4.Replace the air cleaner cover and be sure to snap the two latches closed.

33

Image 37
Contents OPERATOR’S Manual STC48V-22FS-LE Remember Your Mower is only AS Safe AS the OperatorTable of Contents Following Section Limited Warranty Commercial EquipmentIntroduction General InformationDirection Reference Servicing The Engine and Drive Train ComponentsSymbol Description SymbolsSignal Words Safety InformationBefore Operation considerations Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-over protection systemSeat Belt Inspection Using a spark arrestor Maintenance Considerations & storageSPARK Ignition System Install Belt COvER Before Safety and Instructional DecalsEngine SpecificationsElectrical TractorCutter Deck Weights and Dimensions 48V 52V 61VHydraulic System ProductivityControls and Instrument Identification Operating InstructionsInitial RUN-IN Procedures Safety Interlock SystemGround Travel and Steering Starting the EngineForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesHillside Operation Rotating BladesParking the Mower After OperationMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Deck Release Lever Towing optional hitch accessoryCondition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Parking Brake Adjustment AdjustmentsTravel Adjustments Tracking Adjustment Neutral AdjustmentBelt Adjustment Throttle Control and Choke AdjustmentsCutter Deck Adjustments Belt AlignmentCutter Deck Pitch Cutter Deck Height Adjustment ROD Lock NUTPosition Custom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelSection Engine AIR Cleaner Charging the Battery BatteryJump Starting Drive Belts Blade ReplacementCutter Blades Blade InspectionBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts List48V & 52V Cutter Decks Description 61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 423912 Bracket, Fuel Valve STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat 483386 Seat Assembly Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Steering Components Brake Components Brake Components Hydraulic System Available through the individual engine manufacturer Engine STC Fuel System EPA Phase STC Fuel System EPA Phase 3 models produced after 1/1/2011 Models produced after 1/1/2011 STC Fuel System EPA PhaseSTC Fuel System C.A.R.B. Tier STC Fuel System C.A.R.B. Tier Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Heavy-Duty Replacement Decals and Information Plates482166R STC 2009 RDP2 PTO Switch Diode KEY Electrical Schematic Briggs & Stratton / KohlerPlug Electrical Schematic KawasakiLimited Warranty Commercial Equipment

STC48V-22FS, STC52V-24FX, STC48V-22FS-LE, STC61V-27CV specifications

Scag Power Equipment has a longstanding reputation for producing high-quality zero-turn mowers, and the models STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS stand out for their exceptional performance, durability, and innovative technologies.

The STC61V-27CV is equipped with a robust 27 HP Kohler engine, providing ample power for cutting through tough grass and elevating efficiency in landscaping tasks. Its 61-inch Velocity Plus cutting deck ensures a superior mowing experience, delivering precise cuts with the ability to handle various turf conditions. This model features a comfortable seat and ergonomic controls, ensuring maximum operator comfort during extended use. Additionally, the cutting height can be easily adjusted from 1 to 5 inches, allowing users to customize their mowing to suit different grass types and preferences.

Meanwhile, the STC48V-22FS-LE boasts a compact design ideal for residential and commercial properties. Powered by a 22 HP Kawasaki engine, this model is equipped with a 48-inch cutting deck, which offers a perfect balance between maneuverability and cutting capacity. The LE package includes luxurious features such as a high-back seat for added comfort and easy access to maintenance points, ensuring that the mower remains in peak condition. The model's easy-to-use controls and responsive steering make it an excellent choice for first-time users.

The STC52V-24FX offers a blend of power and versatility with its 24 HP Kawasaki engine and 52-inch cutting deck. This model is designed for those who require a longer run-time and increased productivity. The mower features an innovative grass catcher option, making it easier to collect clippings for a tidy finish. Furthermore, the heavy-duty frame enhances structural integrity, while the commercial-grade components ensure long-lasting service.

Lastly, the STC48V-22FS enhances user experience with its practical features. Similar to other models, it features a 22 HP Kawasaki engine coupled with a 48-inch cutting deck, tailored for residential lawns and smaller commercial properties. The mower’s compact design and efficient grass discharge system optimize cutting performance while minimizing downtime.

Overall, Scag Power Equipment offers a wide range of high-performance zero-turn mowers. Each model, including the STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS, incorporates advanced technologies and superior engineering to meet the demands of any lawn care professional or dedicated homeowner. With a commitment to innovation and quality, Scag continues to set the standard for excellence in outdoor power equipment.