Scag Power Equipment STC48V-22FS-LE, STC61V-27CV Starting the Engine, Ground Travel and Steering

Page 18

R

Section 4

4.4 STARTING THE ENGINE

CAUTION

DO NOT USE STARTING FLUIDS. Use of starting fluids in the air intake system may be potentially explosive or cause a “runaway” engine condition that could result in engine damage and/or personal injury.

1.Be sure the fuel shutoff valve, located behind the operator's seat, is completely open. (See Section 7.5.)

2.Secure the ROPS in the upright and locked position.

3.Sit in the operator’s seat, fasten seat belt and place the steering control levers in the neutral position.

4.Engage the parking brake.

5.Place the PTO switch in the disengaged position.

6.If the engine is cold, choke the engine as needed.

7.Move the engine throttle control to about half engine speed.

8.Turn the ignition key to the START position and release the key as soon as the engine starts. Do not hold the key in the START position for more than 15 seconds at a time. Allow at least 60 seconds between each cranking attempt to prevent overheating of the starter motor. Prolonged cranking can damage the starter motor and shorten battery life.

Learn to feather the steering controls to obtain a smooth operating action.

Practice operating the mower until you are comfortable with the controls before proceeding to mow.

Forward Travel

To travel forward with the mower, disengage the parking brake, pull levers inward out of the neutral lock position and slowly push the steering control levers forward an equal distance. The further the steering control levers are pushed forward the greater the forward speed will be. To increase the speed, push the steering control levers further forward and to decrease the speed, pull the steering control levers back.

To stop the forward travel, pull the steering control levers back to the neutral position.

To steer the mower left while traveling forward, pull the left steering lever back.The further the lever is pulled back, the quicker the mower will turn left.

To steer the mower right while traveling forward, pull the right steering control lever back. The further the lever is pulled back, the quicker the mower will turn right.

- NOTE -

Smooth operation of the steering levers will produce smooth mower operation. While learning the operation of the steering controls, keep the travel speed low.

9. Allow engine to warm before operating the mower.

4.5 GROUND TRAVEL AND STEERING

- IMPORTANT -

If you are not familiar with the operation of a machine with lever steering and/or hydrostatic transmissions, the steering and ground speed operations should be learned and practiced in an open area, away from buildings, fences, or obstructions.

Learn the operation on flat ground before operating on slopes.

Start practicing with a slow engine speed and slow forward travel.

14

- IMPORTANT -

Do not travel forward over a curb. The mower will hang up on the curb. Raise the deck and travel backwards over the curb at a 45 degree angle. (See Figure 4-1 items 12-14 for cutter deck raising description.)

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator STC48V-22FS-LETable of Contents Limited Warranty Commercial Equipment Following SectionDirection Reference General InformationIntroduction Servicing The Engine and Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation considerations Know the function of all controls and how to stop quickly Operation ConsiderationsSection Roll-over protection system Foldable Roll-Over Protection SystemSeat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSPARK Ignition System Safety and Instructional Decals Install Belt COvER BeforeElectrical SpecificationsEngine TractorHydraulic System Weights and Dimensions 48V 52V 61VCutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Rotating BladesHillside Operation After OperationAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch accessory Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Cut, or Rough ContourScalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment Tracking AdjustmentCutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightCustom-Cut Baffle Adjustment Position Custom-Cut Baffle AdjustmentElectric clutch adjustment 10. Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilSection Engine AIR Cleaner Battery Charging the BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 423912 Bracket, Fuel Valve STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat 483386 Seat Assembly Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Steering Components Brake Components Brake Components Hydraulic System Available through the individual engine manufacturer Engine STC Fuel System EPA Phase STC Fuel System EPA Phase 3 models produced after 1/1/2011 STC Fuel System EPA Phase Models produced after 1/1/2011STC Fuel System C.A.R.B. Tier STC Fuel System C.A.R.B. Tier Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Replacement Decals and Information Plates Heavy-Duty482166R STC 2009 RDP2 Electrical Schematic Briggs & Stratton / Kohler PTO Switch Diode KEYElectrical Schematic Kawasaki PlugLimited Warranty Commercial Equipment

STC48V-22FS, STC52V-24FX, STC48V-22FS-LE, STC61V-27CV specifications

Scag Power Equipment has a longstanding reputation for producing high-quality zero-turn mowers, and the models STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS stand out for their exceptional performance, durability, and innovative technologies.

The STC61V-27CV is equipped with a robust 27 HP Kohler engine, providing ample power for cutting through tough grass and elevating efficiency in landscaping tasks. Its 61-inch Velocity Plus cutting deck ensures a superior mowing experience, delivering precise cuts with the ability to handle various turf conditions. This model features a comfortable seat and ergonomic controls, ensuring maximum operator comfort during extended use. Additionally, the cutting height can be easily adjusted from 1 to 5 inches, allowing users to customize their mowing to suit different grass types and preferences.

Meanwhile, the STC48V-22FS-LE boasts a compact design ideal for residential and commercial properties. Powered by a 22 HP Kawasaki engine, this model is equipped with a 48-inch cutting deck, which offers a perfect balance between maneuverability and cutting capacity. The LE package includes luxurious features such as a high-back seat for added comfort and easy access to maintenance points, ensuring that the mower remains in peak condition. The model's easy-to-use controls and responsive steering make it an excellent choice for first-time users.

The STC52V-24FX offers a blend of power and versatility with its 24 HP Kawasaki engine and 52-inch cutting deck. This model is designed for those who require a longer run-time and increased productivity. The mower features an innovative grass catcher option, making it easier to collect clippings for a tidy finish. Furthermore, the heavy-duty frame enhances structural integrity, while the commercial-grade components ensure long-lasting service.

Lastly, the STC48V-22FS enhances user experience with its practical features. Similar to other models, it features a 22 HP Kawasaki engine coupled with a 48-inch cutting deck, tailored for residential lawns and smaller commercial properties. The mower’s compact design and efficient grass discharge system optimize cutting performance while minimizing downtime.

Overall, Scag Power Equipment offers a wide range of high-performance zero-turn mowers. Each model, including the STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS, incorporates advanced technologies and superior engineering to meet the demands of any lawn care professional or dedicated homeowner. With a commitment to innovation and quality, Scag continues to set the standard for excellence in outdoor power equipment.
Top Page Image Contents