Scag Power Equipment STC52V-24FX Cutter Deck, Hydraulic System, Productivity, 48V 52V 61V

Page 15

Section 3					R

Tire Pressure:
Front Caster					25 PSI
Drive					12 PSI
Fuel Tanks	Dual (4 Gal. RH, 3 Gal. LH) Seamless Polyethylene Tanks with Large Opening and Fuel Cap
Seat				Padded, Thick Cushion with Extra Spring Support
Travel Speed:
Forward					0 up to 10 MPH
Reverse					0 up to 5 MPH
-NOTE- The machine will travel up to 10 mph for transport purposes. For best cutting performance the forward
travel speed should be adjusted depending upon the cutting conditions.
3.4 Cutter Deck
Type	Floating, Adjustable, Anti-Scalping, Hybrid Design Combines Out-Front and Belly-Mount Designs
Construction				Tri-plate deck construction
	Top of deck consists of three steel plates totaling nearly 1/2" of steel,7-gauge (3/16") deck skirt.
True Cutting Width:
48V					48" (122.0 cm)
52V					52" (132.0 cm)
61V					61" (154.94 cm)
Cutting Height Adjustment		Foot-Operated Lever Adjustment from Operator's Seat, 1.00" to 5.5" in 1/4"increments
Cutter Blades			0.197 in. Thick, Milled Edge, Wear Resistant Marbain™
Blade Engagement			Electric Blade Engagement Clutch with Control Panel Switch
				Connected to the Cutter Deck through a Belt.
Discharge Opening		Extra Wide Discharge Opening with Spring-Loaded Discharge Chute and Turbo Baffle
Discharge Chute				Black, Polypropylene (Plastic), Flexible
Spindles		Heavy-Duty 1-1/8" Top Dimension Spindle Shaft, Cast Housing, Taper Roller Bearing,
		Low Maintenance with Top Access Grease Fitting and Grease Overfill Relief Poppet
Spindle Pulleys				Split Steel with Easily Removed Taper Hubs
Cutter Deck Belts		B-section and Cogged Type with Kevlar Cord. Self-Adjusting, Self-Tightening
Electric Clutch Type				Ogura Heavy Duty PTO Clutch Brake
3.5 Hydraulic System
Hydraulic Oil Filter				10 Micron Spin-on Element Type
Hydraulic Reservoir				Nylon; 2-1/2 Quart Capacity
3.6 Weights and Dimensions			48V	52V	61V
Length			80"	80"	80"
Tracking Width			46.5"	46.5"	46.5"
Overall Width w/chute down			60.5"	64.5	73.5"
Overall Width w/chute up			49"	53"	62"
Overall Height w/ROPS (up on Folding Models)			......................... 66"	66"	66"
Overall Height w/ROPS down (Folding Models)			54"	54"	54"
Operating Weight w/ROPS			1050#	1100#	1150#
3.7 PRODUCTIVITY			48V	52V	61V
Cutting Width			48"	52"	61"
Acres Per Day			18.6	20.2	23.7

The preceding chart will aid you in determining how many acres your Scag mower will cut per day. The chart is an estimate based on 8 hours per day cutting time at 6 MPH with a 20% allowance for overlap and turns.

11

Image 15

Contents

OPERATOR’S Manual STC48V-22FS-LE Remember Your Mower is only AS Safe AS the OperatorTable of Contents Following Section Limited Warranty Commercial EquipmentServicing The Engine and Drive Train Components General InformationIntroduction Direction ReferenceSymbol Description SymbolsSafety Information Signal WordsBefore Operation considerations Operation Considerations Know the function of all controls and how to stop quicklySection Foldable Roll-Over Protection System Roll-over protection system Seat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSPARK Ignition System Install Belt COvER Before Safety and Instructional DecalsTractor SpecificationsEngine ElectricalProductivity Weights and Dimensions 48V 52V 61VCutter Deck Hydraulic SystemControls and Instrument Identification Operating InstructionsInitial RUN-IN Procedures Safety Interlock SystemStarting the Engine Ground Travel and SteeringForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesAfter Operation Rotating BladesHillside Operation Parking the MowerAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Deck Release Lever Towing optional hitch accessoryCondition Cause Cure Troubleshooting Cutting ConditionsCut, or Rough Contour Troubleshooting Cutting Conditions ContdScalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Tracking Adjustment Neutral AdjustmentBelt Alignment Throttle Control and Choke AdjustmentsBelt Adjustment Cutter Deck AdjustmentsCutter Deck Pitch Cutter Deck Height Adjustment ROD Lock NUTPosition Custom-Cut Baffle Adjustment Custom-Cut Baffle Adjustment10. Clutch Air Gap Adjustment Electric clutch adjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelSection Engine AIR Cleaner Battery Charging the BatteryJump Starting Blade Inspection Blade ReplacementDrive Belts Cutter BladesBODY, DECK, and Upholstery TiresScag Approved Attachments and Accessories Illustrated Parts List48V & 52V Cutter Decks Description 61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 423912 Bracket, Fuel Valve STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat 483386 Seat Assembly Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Steering Components Brake Components Brake Components Hydraulic System Available through the individual engine manufacturer Engine STC Fuel System EPA Phase STC Fuel System EPA Phase 3 models produced after 1/1/2011 Models produced after 1/1/2011 STC Fuel System EPA PhaseSTC Fuel System C.A.R.B. Tier STC Fuel System C.A.R.B. Tier Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Heavy-Duty Replacement Decals and Information Plates482166R STC 2009 RDP2 PTO Switch Diode KEY Electrical Schematic Briggs & Stratton / KohlerPlug Electrical Schematic KawasakiLimited Warranty Commercial Equipment