Scag Power Equipment STC61V-27CV, STC48V-22FS-LE, STC52V-24FX operating instructions Section

Page 36

R

Section 7

C. CHANGING HYDRAULIC OIL FILTER ELEMENT

The hydraulic oil filter should be changed after every 500 hours of operation or annually, whichever occurs first.

1.Remove the oil filter element and properly discard it. See Figure 7-3. Fill the new filter with clean oil and install the filter. Hand tighten only.

2.Run the engine at idle speed with the speed control lever in neutral for five minutes.

3.Check the oil level in the hydraulic tank. It must be 3-1/4" inches from the top of the filler neck. If necessary, add SAE 20W50 motor oil.

A. CHECKING ENGINE CRANKCASE OIL LEVEL

The engine oil level should be checked after every 8 hours of operation or daily as instructed in the Engine Operator’s Manual furnished with this mower.

B. CHANGING ENGINE CRANKCASE OIL

After the first 20 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or bi-weekly, whichever occurs first. Refer to the Engine Operator’s Manual furnished with this mower for instructions.

7.4 ENGINE OIL

ENGINE OIL

FILLER

ENGINE OIL

FILTER

Figure 7-4. Briggs & Stratton Engine Oil Fill/Dipstick,

and Filter Locations

ENGINE OIL

FILLER

ENGINE OIL

FILTER

Figure 7-5. Kohler / Kawasaki Engine Oil Fill/Dipstick,

and Filter Locations

C. CHANGING ENGINE OIL FILTER

After the first 20 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for instructions. See Figure 7-4 or Figure 7-5.

7.5 ENGINE FUEL SYSTEM

DANGER

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

A. FILLING THE FUEL TANK

Fill the fuel tank at the beginning of each operating day. For EPA Phase 2 (produced prior to 1/1/2011) models, fill to within one (1) inch below the filler neck. For Low Emission (LE) and EPA Phase 3 (produced after 1/1/2011) models, fill to the bottom of the filler neck insert (approximately 4 gallons RH Fuel Tank and 3 Gallons LH Fuel Tank) at the beginning of each operating day. See Figure 7-6. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87 and a maximum of 10% Ethanol.

DO NOT use E85 Fuel. Using E85 Fuel will cause severe damage to the engine.

32

Page 35 Page 37
Image 36
Page 35 Page 37
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator STC48V-22FS-LETable of Contents Limited Warranty Commercial Equipment Following SectionGeneral Information IntroductionDirection Reference Servicing The Engine and Drive Train ComponentsSymbols Symbol DescriptionSafety Information Signal WordsBefore Operation considerations Know the function of all controls and how to stop quickly Operation ConsiderationsSection Roll-over protection system Foldable Roll-Over Protection SystemSeat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSPARK Ignition System Safety and Instructional Decals Install Belt COvER BeforeSpecifications EngineElectrical TractorWeights and Dimensions 48V 52V 61V Cutter DeckHydraulic System ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresStarting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelRotating Blades Hillside OperationParking the Mower After OperationAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch accessory Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Cut, or Rough ContourScalping Blades Hitting Adjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Adjustments Belt AlignmentAdjustment ROD Lock NUT Cutter Deck Pitch Cutter Deck HeightCustom-Cut Baffle Adjustment Position Custom-Cut Baffle AdjustmentElectric clutch adjustment 10. Clutch Air Gap AdjustmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd LubricationLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilSection Engine AIR Cleaner Battery Charging the BatteryJump Starting Blade Replacement Drive BeltsCutter Blades Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 423912 Bracket, Fuel Valve STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat 483386 Seat Assembly Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Steering Components Brake Components Brake Components Hydraulic System Available through the individual engine manufacturer Engine STC Fuel System EPA Phase STC Fuel System EPA Phase 3 models produced after 1/1/2011 STC Fuel System EPA Phase Models produced after 1/1/2011STC Fuel System C.A.R.B. Tier STC Fuel System C.A.R.B. Tier Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Replacement Decals and Information Plates Heavy-Duty482166R STC 2009 RDP2 Electrical Schematic Briggs & Stratton / Kohler PTO Switch Diode KEYElectrical Schematic Kawasaki PlugLimited Warranty Commercial Equipment

STC48V-22FS, STC52V-24FX, STC48V-22FS-LE, STC61V-27CV specifications

Scag Power Equipment has a longstanding reputation for producing high-quality zero-turn mowers, and the models STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS stand out for their exceptional performance, durability, and innovative technologies.

The STC61V-27CV is equipped with a robust 27 HP Kohler engine, providing ample power for cutting through tough grass and elevating efficiency in landscaping tasks. Its 61-inch Velocity Plus cutting deck ensures a superior mowing experience, delivering precise cuts with the ability to handle various turf conditions. This model features a comfortable seat and ergonomic controls, ensuring maximum operator comfort during extended use. Additionally, the cutting height can be easily adjusted from 1 to 5 inches, allowing users to customize their mowing to suit different grass types and preferences.

Meanwhile, the STC48V-22FS-LE boasts a compact design ideal for residential and commercial properties. Powered by a 22 HP Kawasaki engine, this model is equipped with a 48-inch cutting deck, which offers a perfect balance between maneuverability and cutting capacity. The LE package includes luxurious features such as a high-back seat for added comfort and easy access to maintenance points, ensuring that the mower remains in peak condition. The model's easy-to-use controls and responsive steering make it an excellent choice for first-time users.

The STC52V-24FX offers a blend of power and versatility with its 24 HP Kawasaki engine and 52-inch cutting deck. This model is designed for those who require a longer run-time and increased productivity. The mower features an innovative grass catcher option, making it easier to collect clippings for a tidy finish. Furthermore, the heavy-duty frame enhances structural integrity, while the commercial-grade components ensure long-lasting service.

Lastly, the STC48V-22FS enhances user experience with its practical features. Similar to other models, it features a 22 HP Kawasaki engine coupled with a 48-inch cutting deck, tailored for residential lawns and smaller commercial properties. The mower’s compact design and efficient grass discharge system optimize cutting performance while minimizing downtime.

Overall, Scag Power Equipment offers a wide range of high-performance zero-turn mowers. Each model, including the STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS, incorporates advanced technologies and superior engineering to meet the demands of any lawn care professional or dedicated homeowner. With a commitment to innovation and quality, Scag continues to set the standard for excellence in outdoor power equipment.
Top Page Image Contents