RedMax BCZ2500SW manual SE6, SE7 SE8 SE9 Mounting Engine SE5, Putting on Waist PAD,  14 

Page 14

6.Set up (BCZ2500SW)

SE5

SE6

SE7

SE8

(1)

(2)

SE9

■MOUNTING ENGINE (SE5)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly.

3.Fasten the clamp securely with two screws.

IMPORTANT

Tighten the screws gradually by turns.

■INSTALLING HANDLE

•Mount the handle to the shaft tube and clamp it at a location that is comfortable to you. (SE6)

(1) About 14.5 inches (37cm)

■CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE7)

■CONNECTING SWITCH WIRES

•Connect the switch wires between the engine and the main unit. Pair the wires of the same color. (SE7)

■PUTTING ON WAIST PAD

•Wrap the waist pad around the shaft tube and the throttle wire. (SE8)

(1)Waist Pad

(2)Band

■INSTALLING DEBRIS GUARD

•Put the debris guard on the gear box, attach it with the 4 screws and hardware provided. (SE9)

(1)Debris guard

(2)Plate

(3)Washer

(4)Screw

14 

Image 14

Contents BCZ2500SW T3002-93111BCZ2500S BCZ2500SUPage Safety First ContentsBCZ2500S/BCZ2500SU/BCZ2500SW Overall sizeLxWxH SpecificationsParts location  4  5   6  Symbols on the machineType de moteur 1KZXS.0254QR EM Cylindrée du moteur 25,4cc Working Circumstance For safe operationWorking Condition Working Plan  8  9  Before Starting the EngineStarting the Engine Using the Product  10  Handling Fuel Maintenance If Someone Comes  11 Transportation  12  13  SE7 SE8 SE9 Mounting Engine SE5 SE5SE6 Putting on Waist PADSE10 SE11 Set upInstalling Cutting Head SE10 Balance Unit 16  HOW to MIX FuelFuel Recommended Mixing Ratio Gasoline 50OIL 17  Fueling the UnitFor Your Engine LIFE, Avoid Starting Engine OperationOP1 OP4 19   20  Adjusting the Line LengthOP7 For safety reasons, do not use metalreinforced line MaintenanceMaintenance Chart MA1 MA2 MA3 MA4 Refilling Trimming Line 22  Gear Case MA9 MA8 MA9Spark Arrester Intake AIR Cooling VentCylinder Intake air cooling vent back Procedures to be Performed After Every 100 Hours of USEMA101 MA11  24 Storage  25 Optional blade usage  26 OPT5 OPT6 OPT3BCZ2500SU OPT4 Cutting MethodOperation OPT7 OPT8 28  Controlling Blade BounceHow you can maintain the best control What causes kick outHow you can reduce the chance of kick out  29  30  OPT9 Maintenance BladeTransporting the Unit  31  Troubleshooting guideCheck Probable Causes Action  32  Parts list  33  34  Optional Blade & Accessories  35 Drive Unit BCZ2500SW S/N 100001 and up  36 Optional Blade  37  38  BCZ2500S S/N 35208 and up BCZ2500SU S/N 35208 and up  39 Manufacturer’s warranty coverage RedMax 2-YEAR Limited Warranty RedMax Garantie limitée à 2 ans