RedMax GZ3500T Operating the Engine, Starting the Engine Normal start, Checking the OIL Supply

Page 11

GZ3500T

7. Operating the Engine

WARNING

It is very dangerous to run a chainsaw with mounts broken or any missing parts.

Before starting engine, make sure that all the parts includ- ing bar and chain are installed properly.

■STARTING THE ENGINE Normal start

1.Fill fuel and chain oil tanks respectively, and tighten the caps securely.

Chain oil

Fuel

2.Continuously push the priming bulb until fuel comes in the bulb. Then press additional 5 times.

3. Set the switch to “I” position.

Switch

Throttle interlock

Throttle lever

4. Turn the choke knob to the closed position.

Choke

Open with

Choke

closed

throttle lever

open

NOTE

When restarting immediately after stopping hot en- gine, choke knob should be in the open position.

5.While holding the saw unit securely on the ground, pull the starter rope using short strokes vigorously.

WARNING

Do not start the engine while the chain saw hangs in one hand. The saw chain may touch your body. This

 

is very dangerous.

 

6.

When engine has started, turn the choke knob to

 

 

the closed position and then pull the starter again to

 

 

run the engine.

 

7.

Allow the engine to warm up with the throttle lever

U

 

pulled slightly.

■ CHECKING THE OIL SUPPLY

S

 

 

WARNING

 

Make sure the bar and the chain is in place when checking the oil supply.

If not, the rotating parts may be exposed. It is very dangerous.

After starting the engine, run the chain at medium speed and see if chain oil is scattered off as shown in the fig- ure.

Chain oil

The chain oil flow can be changed by inserting a screwdriver in the hole on bottom of the clutch side. Adjust according to your work conditions.

Chain oil flow adjusting shaft

Rich Lean

The oil tank should become nearly empty by the time fuel is used up. Be sure to refill the oil tank every time when refueling the saw.

NOTE

The adjustment range of the discharge is 90°. Pay at- tention not to turn any further, as this may damage the adjuster of the oil pump.

■ADJUSTING THE CARBURETOR

Idle adjusting screw

H needle

L needle

The carburetor on your unit has been factory adjusted, but may require fine tuning due to a change in operat- ing conditions.

Before adjusting the carburetor, make sure that the pro- vided air/fuel filters are clean and fresh and the fuel prop- erly mixed.

When adjusting, take the following steps:

NOTE

Be sure to adjust the carburetor with the bar chain at- tached.

US-11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents GZ3500T Contents Parts location SpecificationsGZ3500T Power unit US-4 Basic Safety RulesBecause of high temperature For safe operationTransport Fuel SafetyBefore USE CuttingDisposal Kickback Safety Precautions For Chain SAW UsersUS-7 Symbols on the MachineEmission Control An emission control label is located on the enginePay attention to the correct direction of the saw chain Installing Guide Bar and Saw ChainStandard saw unit package contains the items as illustrated OIL Requirements Fuel and Chain OilFuel Gasoline RequirementsFor Your Engine LIFE, Avoid Redmax TWO-STROKE Engine WarrantyHOW to MIX Fuel Recommended Mixing Ratio Gasoline 50 OIL Fueling the UnitTurn the choke knob to the closed position Adjusting the CarburetorOperating the Engine Starting the Engine Normal startStopping the Engine SawingChain Brake Releasing the BrakeFelling a Tree Periodical Service Points MaintenanceMaintenance After Each USE US-15 Maintenance of Saw Chain and Guide BarSaw Chain Case 1. Starting failure Troubleshooting GuideCase 2. Lack of power/Poor acceleration/ Rough idling DisposalUS-17 Manufacturer’s warranty coverageUS-18 Limited Warranty

GZ3500T specifications

The RedMax GZ3500T is a robust and versatile power equipment solution designed for professional landscapers and avid gardening enthusiasts alike. This high-performance tool stands out with its innovative features, powerful engine, and user-friendly design.

At the heart of the GZ3500T is a powerful 35cc 2-stroke engine, delivering impressive power and efficiency to handle a variety of tasks. This engine is designed to provide maximum torque and consistent performance, making it ideal for tackling thick grass and heavy brush with ease. The incorporation of RedMax's advanced Smart Start technology ensures that starting the engine is effortless, reducing pull resistance for easy ignition.

One of the standout features of the GZ3500T is its high-quality cutting system. The trimmer is equipped with a professional-grade double-line cutting head, allowing for swift cutting action and a clean finish. The cutting width of the GZ3500T is optimal for both narrow and wide spaces, making it suitable for both precise trimming and larger areas. The auto-feed head simplifies the process of line replacement, ensuring that users can quickly get back to their work without tedious interruptions.

User comfort and ergonomics are paramount in the design of the GZ3500T. Its lightweight construction, combined with a well-balanced design, minimizes fatigue during prolonged use. The adjustable handlebars offer customization for users of different heights, enhancing control and maneuverability. Additionally, the unit features a padded harness system that distributes weight evenly across the shoulders, further increasing comfort during operation.

Durability is another key characteristic of the RedMax GZ3500T. Built with high-quality materials and components, this trimmer is designed to withstand the rigors of professional use. The fuel tank is built for efficiency, allowing for longer run times between refueling. Furthermore, the engine is engineered to reduce emissions, complying with environmental regulations while providing a cleaner operation.

In summary, the RedMax GZ3500T is a top-tier trimmer that combines power, efficiency, and comfort. With its cutting-edge technologies, user-centric design, and durability, it serves as an essential tool for anyone looking to achieve a pristine landscape. Whether used for commercial purposes or personal projects, the GZ3500T proves to be an indispensable ally in the field.
Top Page Image Contents