RedMax HEZ2500S manual  20 , Operation, ADJUSTING IDLING SPEED OP8

Page 20

20 

8. Operation

OP8

(1)

OP9

20 

■ADJUSTING IDLING SPEED (OP8)

1.When the engine tends stop frequently at idling mode, turn the adjusting screw clockwise.

2.When the cutting head keeps rotating after releasing the trigger, turn the adjusting screw counter-clockwise.

(1) idle adjusting screw

NOTE

•Warm up the engine before adjusting the idling speed.

■HOW TO USE

WARNING

1Always wear eye protection such as safety goggles. Never lean over the rotating cutting head. Rocks or other debris could be thrown into eyes and face and cause serious personal injury.

2Keep the blade guard and the mad guard attached in place at all times when the unit is operated.

3Before starting a job, check the area and remove all obstacles and objects that could be thrown by the blade.

4Do not adjust the wheel height or try to remove anything entangled to the blade with the engine running.

1Before starting the engine, adjust the wheel height for desired cutting depth(See page 18).

2Before starting a job, plan your direction of travel so that you can always hold the edger on you right side and can walk on a hard surface as much as possible.

3When starting to edge, run the engine at full throttle, and slowly have the blade cut into the edge groove.

NOTE

•Do not use the HEZ2500S to make a new groove into the ground. Such usage will not be covered by RedMax Warranty.

Image 20

Contents HEZ2500S STICK EDGERSOWNER / OPERATOR MANUAL WARNING WARNINGPage SAFETY FIRST 1. Parts location  4 HEZ2500S 2. Specifications 5  3. Warning labels on the machine  6 4. Symbols on the machine  7 IMPORTANT ENGINE INFORMATION INFORMATION IMPORTANTE CONCERNANT LE MOTEUR5. For safe operation  8 4 Thick work gloves 5 Non-slip-sole work boots WORKING CONDITION 9  WORKING PLANSTARTING THE ENGINE  10 BEFORE STARTING THE ENGINE  11  USING THE PRODUCTIF SOMEONE COMES  12 MAINTENANCE TRANSPORTATION  13 HANDLING FUEL 6. Set up  14 CONNECTING THROTTLE WIRE CONNECTING SWITCH WIRES 15  SE5 SE6 SE71 Blade mounting bolt Left-handed 2 Cutter holder B 3 Blade 4 Bar 5 Cutter holder A7. Fuel  16 FOR YOUR ENGINE LIFE, AVOID  17 FUELING THE UNIT 8. Operation  18 ADJUSTING HANDLE POSITION ADJUSTING WHEEL HEIGHT 19  1 choke lever 2 close 3 open 4 ignition switch 5 start 6 stopADJUSTING THROTTLE CABLE 1 cable adjuster 20  ADJUSTING IDLING SPEED OP89. Maintenance  21 Things to check before using stick edger BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGER 22  AIR FILTER 23  MA511 cylinder 2 intake air cooling vent back  24 PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 10. Storage  25 11. Troubleshooting guide  26 12. Parts list  27  28  Fig.1 DRIVE UNIT HEZ2500S S/N 000000 and up 29  Key# 30  Fig.2 ENGINE UNIT HEZ2500S S/N 015257 and up 31  CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSManufacturer’s warranty coverage Owner’s warranty responsibilities4344 Shackleford Road Suite Norcross, Georgia RedMax STICK EDGER MODEL HEZ2500S 2-YEAR LIMITED WARRANTYKOMATSU ZENOAH AMERICA INC Il nexiste aucune autre garantie explicite RedMax STICK EDGER Modèle HEZ2500S Garantie limitée à 2 anslimites de la garantie Page Printed in Japan KOMATSU ZENOAH AMERICA INC 4344 Shackleford Road SuiteNorcross, Georgia