RedMax HEZ2500S manual Set up,  14 , MOUNTING ENGINE SE1, SE2 SE3 SE4, Connecting Throttle Wire

Page 14

6. Set up

6. Set up

SE1

■MOUNTING ENGINE (SE1)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the clutch housing and the shaft tube and install the screw. When difficult to engage, twist the engine slightly.

3.Fasten the clamp securely with two screws.

SE2

SE3

SE4

IMPORTANT

Tighten the screws gradually by turns.

■CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2)

■CONNECTING SWITCH WIRES

•Connect the switch wires between the engine and the main unit. Pair the wires of the same color.

■MOUNTING OTHER PARTS

1.Insert the driveshaft into the clutch drum, then attach the gearbox to the shaft tube as aligning the positioning holes. Wipe out grease on the tube and the inside of the gearbox. Screw in the lock screw and fasten the clamp bolt firmly. (SE3)

(1)Clamp bolt

(2)Lock screw

2.Install the blade guard to the gear case with the provided 3 screws, then clamp it to the shaft tube with 2 screws. (SE4)

14 

Image 14

Contents OWNER / OPERATOR MANUAL HEZ2500SSTICK EDGERS WARNING WARNINGPage SAFETY FIRST 1. Parts location  4 HEZ2500S 2. Specifications 5  3. Warning labels on the machine  6 IMPORTANT ENGINE INFORMATION 4. Symbols on the machine 7  INFORMATION IMPORTANTE CONCERNANT LE MOTEUR4 Thick work gloves 5 Non-slip-sole work boots 5. For safe operation 8  WORKING CONDITION 9  WORKING PLANSTARTING THE ENGINE  10 BEFORE STARTING THE ENGINE  11  USING THE PRODUCTIF SOMEONE COMES  12 MAINTENANCE TRANSPORTATION  13 HANDLING FUEL CONNECTING THROTTLE WIRE 6. Set up 14  CONNECTING SWITCH WIRES1 Blade mounting bolt Left-handed 2 Cutter holder B 3 Blade 4 Bar  15 SE5 SE6 SE7 5 Cutter holder A7. Fuel  16 FOR YOUR ENGINE LIFE, AVOID  17 FUELING THE UNIT ADJUSTING HANDLE POSITION 8. Operation 18  ADJUSTING WHEEL HEIGHTADJUSTING THROTTLE CABLE  19 1 choke lever 2 close 3 open 4 ignition switch 5 start 6 stop 1 cable adjuster 20  ADJUSTING IDLING SPEED OP8Things to check before using stick edger 9. Maintenance 21  BE SURE TO CHECK THE FOLLOWING BEFORE USING YOUR STICK EDGER 22  AIR FILTER 23  MA511 cylinder 2 intake air cooling vent back  24 PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 10. Storage  25 11. Troubleshooting guide  26 12. Parts list  27  28  Fig.1 DRIVE UNIT HEZ2500S S/N 000000 and up 29  Key# 30  Fig.2 ENGINE UNIT HEZ2500S S/N 015257 and up 31  Manufacturer’s warranty coverage CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONS Owner’s warranty responsibilities4344 Shackleford Road Suite Norcross, Georgia RedMax STICK EDGER MODEL HEZ2500S 2-YEAR LIMITED WARRANTYKOMATSU ZENOAH AMERICA INC Il nexiste aucune autre garantie explicite RedMax STICK EDGER Modèle HEZ2500S Garantie limitée à 2 anslimites de la garantie Page Printed in Japan KOMATSU ZENOAH AMERICA INC 4344 Shackleford Road SuiteNorcross, Georgia