Jensen JTA-980 Listening to Tape, Stereo Phonograph Operation, General Operation, Remark

Page 18

LISTENING TO TAPE

GENERAL OPERATION

1.Press the TAPE function button to enter the “TAPE” mode.

2.The system will start playback automatically after inserting the cassette tape.

3.Adjust the volume to the desired level.

4.Press the TAPE FAST FORWARD / EJECT button half way when playing, the tape will be advanced forward rapidly.

5.Slightly press the TAPE FAST FORWARD / EJECT button again to resume normal playback. The button will resume to the outermost position.

6.Press the TAPE FAST FORWARD / EJECT button completely, then the playing will be stopped and the cassette tape will be ejected.

Notes:

-Make sure the direction is correct when inserting the tape.

-Some searching noise can be heard and the system cannot perform normal playback function during fast forward mode.

-To avoid damaging the tape, it is recommended to take the cassette tape out of the deck after listening.

STEREO PHONOGRAPH OPERATION

Note, Before Use:

-Lift up the turntable dust cover until it can hold position.

-Move up the stylus protector.

-Be sure that the tone arm is detached from the tone arm rest before operating, and replace again when finished.

1.Press the PHONO function button to enter the “PHONO” mode.

2.Place the record on the platter, over the center spindle (use the 45 RPM record adaptor when playing 45 RPM record).

3.Set the Speed selector to 33, 45 or 78 RPM according to the record you are playing.

4.Lift the tone arm from the rest and slowly move it over the record. The platter will turn.

5.Move the tone arm to the beginning of the record, or to the start of a particular track. Gently lower the tone arm onto the record to start playing.

6.Adjust the volume to the desired level.

7.When the record is played to the end of the record, the platter will automatically stop rotating. Lift the tone arm and return it to the rest position.

8.To stop the record manually when playing, lift up the tone arm and return it to the rest position.

Remark:

Some types of records may have an auto-stop area outside the preset limit, so the turntable may stop before the last track finishes. In this case, set the auto-stop switch to the “OFF” position. This allows the record to play to the end, but it will not stop automatically. You must manually raise the tone arm and place it back in the rest to stop the turntable from spinning and turn it off.

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents JTA-980 Retain this Booklet for Future ReferenceWe Want You Listening For a Lifetime Dear Jensen CustomerTo establish a safe level Customers RecordImportant Safety Instructions Page Page On Placement On Protection Against Laser Energy ExposureOn Condensation Compliance with FCC Regulations Protect Your FurnitureConnecting the AC Power Cord Getting StartedSpeaker Connection Location of Controls and Indicators Main UnitRemote Control Button DescriptionBattery Installation Battery PrecautionsPlaying Compact Disc Operating InstructionsListening to Radio Playing Compact DiscsSkip Mode Skip Up /Skip Down Play / Pause ModeStop Mode  Random Play Using the Main Unit ControlPlaying Compact Discs in CD-2 Ii Recoding by Program Recording ModeRecording Function on CD-2 II Phonograph RecordingRecording Setting II Erase ONE Track UN-FINALIZE or Erase a CD-RW DiscUN-FINALIZE a CD-RW Disc III Erase ALL TracksGeneral Operation Listening to TapeStereo Phonograph Operation RemarkMute Function Auxiliary InputBass Boost Line OUT ConnectionResetting Care and MaintenanceCassette Care Cleaning the Unit Compact Disc CareTroubleshooting Guide Problem Possible Cause SolutionPower Consumption SpecificationPower Requirement Frequency RangeDAY Limited Warranty and Service Valid in the U.S.A only
Top Page Image Contents