Simplicity 5022285 Mowing Height Adjustment, Foot Pedal Adjustment, To adjust pedal position

Page 34

Troubleshooting, Adjustment & Service

MOWING HEIGHT ADJUSTMENT

The cutting height adjustment pin (A, Figure 31) controls the mower cutting height. The cutting height is adjustable between 1-3/4” (4,4 cm) and 5” (12,7 cm) in 1/4” (0,64 cm) increments.

1.Depress the deck lift foot pedal (B) until it locks into the 5” (12,7 cm) position.

2.Place the cutting height adjustment pin in the desired cutting height.

3.Depress the deck lift foot pedal then push the lock lever (C) towards the right to release the lock.

4.Release the deck lift foot pedal until it comes to rest against the cutting height adjustment pin.

FOOT PEDAL ADJUSTMENT

The deck lift foot pedal can be adjusted to accommodate the operator’s height for optimal comfort.

To adjust pedal position:

1.Remove the foot pedal (A, Figure 32) from the pedal mount tab (B).

2.Remove the pedal mount hardware (C) and rotate the tab 180 degrees.

3.Reinstall the pedal mount hardware and tighten securely.

4.Reinstall the foot pedal on the pedal mount tab in the proper orientation as shown in Figure 32.

	C
B	A
B

Figure 31. Mowing Height Adjustment

A.Cutting Height Adjustment Pin

B.Deck Lift Foot Pedal

C.Deck Lift Lock lever

B

AC

OPTIONAL

POSITION

Figure 32. Foot Pedal Adjustment

A.Deck Lift Foot Pedal

B.Pedal Mount Tab

C.Pedal Mount Hardware

30

Image 34

Contents Press Operator’s ManualsPaper Size BinderyPage 21HP Zero-Turn Riders 23HP Zero-Turn RidersPage Table of Contents General Operation Safety Rules and InformationTransporting and Storage Emissions Slope OperationChildren Towed Equipment RIDE-ON UnitsService & Maintenance Service and MaintenanceSafe Handling of Gasoline Safety Rules & Information Roll BAR InstructionsInspection and Maintenance of the Roll BAR Seat Belt North American Identification NumbersCE Identification TAG Markings CE ModelsDecal Danger, Mower Decal MainPart No Safety DecalsSafety Decals Decal Warning Part NoSafety Interlock System Safety Icons & Interlock SystemOperational Safety Checks Parking Brake PTO Power Take Off SwitchControl Functions ChokeFeatures & Controls General Operating Safety Checks Before StartingStopping the Rider OperationStarting the Engine MowingForward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a Corner Practice Turning In PlaceExecuting Turns To raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltAttaching a Trailer StorageEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursRegular Maintenance Grease LubricationOil Check Hydraulic OIL Level Battery MaintenanceCleaning the Battery and Cables Change Hydraulic OIL FilterServicing the Mower Blades Removing the BladeTroubleshooting Adjustments & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Parking Brake Adjustment Battery Charging To adjust the spring pre-load Rear Suspension Adjustment To adjust the upper mounting position PTO Clutch Adjustment Blade Brake CheckNeutral Adjustment RETURN-TO-NEUTRAL AdjustmentAdjustment Foot Pedal Adjustment Mowing Height AdjustmentTo adjust pedal position Deck Leveling Adjustment 4 SpacersHydraulic Pump Drive Belt Replacement Mower Belt Replacement Mower PTO Belt Idler Arm Stationary Idler PulleyChassis DimensionsEngine Transmissions