G
GARDENA Accu Telescopic Hedge Trimmer THS 42
G
5. Assembly / setting the working position
1. Technical data
Voltage |
| 12 V |
|
|
|
|
|
| |||
Rated current (idling) | 2 A |
| |||
Strokes |
| 2,100/min |
| ||
Blade length | 42 cm |
| |||
Telescopic extension range | 0 - 31 cm |
| |||
Running time with Accu A 12 | 25 - 35 min |
| |||
Weight (without Accu) | 3.2 kg |
| |||
Working area related emission |
|
|
|
| |
characteristic value L PA 1) | 73 dB (A) |
| |||
Noise level | L WA 2) | 92 dB (A) | Measuring method according to | ||
Vibrations | a vhw 1) | < 2.5 dB (A) | 1) EN 774 2) directive 2000/14/EC | ||
|
|
|
|
|
|
5.1Assembly of the guide handle (fig. A)
The three-position guide handle
1 is mounted onto the unit and secured with 2 screws. (Captive screws integrated in the handle.)
5.2Basic working position settings (fig. B - E)
The Telescopic Hedge Trimmer
has three basic settings. These are marked ! to ♣ on the blade head and the handle:
! Trimming hedges from the |
side at a distance from the |
standing position, eg. to reach |
5.3 Setting a working position
Attention! The accu must Abe disconnected from the tool and the cutting blade sheath should remain in posi- tion when setting the working position!
Never take hold of the cutting blade to turn the blade head or to extend the telescopic handle!
Note: The cutting blade has a total of 8 working positions (12° increments from 0°/horizon- tal to 84° elevation).
the desired working length (fig. F). The length of the tele- scopic handle can be extended by max. 310 mm.
2. (Fig. G1) Press and hold the |
oval pimpled button 7 while |
turning the trimmer head A in |
the axial direction into one of |
the working positions !∀ or |
♣ for example into position ♣ |
for trimming the top of a high |
hedge (arrow must point to |
the position number – see |
figure D1). |
Note: The trimmer head can |
be set to one of 7 axial posi- |
2. Notes on operating instructions
Please read these operating in- | operating controls, their correct |
structions carefully and observe | use, and the notes on safety. |
the notes given. | For safety reasons, child- |
Use the instructions to familiarise | |
yourself with the equipment, the | Aren under 16 as well as |
| persons not familiar with these |
operating instructions should not use this Telescopic Hedge Trimmer.
Keep these operating instruc- tions in a safe place.
over flower beds (fig. B/B1). |
Note: |
Telescopic handle retracted. |
∀ For trimming extremely low |
hedges, or eg. ground blan- |
kets, while standing upright |
(fig. C/C1). |
Adjustment to any of the 5 inter- mediate settings for the 3 work- ing positions described above is made in the same manner. The positions !∀ or ♣ de- scribed above are recommended for straight forward handling.
tions between 0° and 180° |
at increments of 30°. |
3. (Fig. G 2) Adjust the cutting |
angle for the trimmer blade |
by pressing and holding the |
round adjusting button 9 while |
adjusting the position of the |
3. Introduction
This Hedge Trimmer is one of the tools in the extensive range of
Please use the following articles from the
1.Accu A 12 (Art. No. 2109) as the energy supply / battery for the
2.Battery Charger NL 12
(Art. No. 2105) as the charger for the
Alternatively, the
This can be recharged using the Battery Charger NL 12 or by the
Important! The
Note: Telescopic handle |
extended to the appropriate |
length for upright working. |
♣For trimming high hedges up to approx. 2.5 m from the ground without the need for a ladder or scaffolding (fig. D/D1).
Note: Telescopic handle ex- tended to the appropriate length. Control of the Tele- scopic Hedge Trimmer is within arm’s reach for easier handling (fig. D).
Important! Always ensure that the selected position snaps in correctly. Danger of injury!
Select one of the basic working positions !∀ or ♣ according to the description section 5.2 and referring to figure E, adjust the Telescopic Hedge Trimmer as follows (fig. D/F/G):
1.(Fig. F) Adjust the length of the telescopic handle by pressing and holding the ad- justing button 6 while extend- ing the telescopic handle to
trimmer blade 8 for working |
as required. |
(Our example: position ♣. |
Arrow must point to the position |
number – see figure D1). |
Note: All 3 working positions |
for selection can be set in this |
way. |
The working position has been |
correctly set when the position |
number indicates the selected |
position (see example figure |
D1). |
4. Proper use
The GARDENA Accu Telescopic Hedge Trimmer is designed for trimming hedges in domestic gardens and allotments.
Gardening tools for private house- holds and gardens are consid- ered unsuitable for use in public grounds, parks, sports centres, in agriculture or forestry.
Compliance with the instructions provided by the manufacturer is a prerequisite for using the tool correctly.
The operating instructions also include the conditions for opera- tion, repair and maintenance.
Attention! Because of Athe danger of physical injuries, this tool must not be used for cutting lawns / grass verges, or for cutting in the sense of shredding for com- posting.
6. Operation (fig. H/I)
Insert the accu 5 in the re- ceptacle as illustrated in figure I. Ensure that the accu snaps in correctly. Pay attention that this audibly “clicks” into position.
The accu is released from the tool by simultaneously pressing both of the orange coloured locking buttons.
The Hedge Trimmer is fitted with a
vent the tool being turned on by accident. Thus both hands are required to operate the Hedge Trimmer (fig. H):
1.Hold by the
handle 1 and press one of the three button switches 2.
2.Hold the grip 3 with the other hand and depress the button switch 4. The Hedge Trimmer will then start to run.
Simply release either of these switches in order to stop the trimmer.
In accordance with safety regu- lations, an additional safety device ensures that the blade motion stops within 1 sec.
The projecting guide (impact protection) prevents any kick- back if the trimmer hits a solid object.
12 | 13 |