Poulan 810 EPT Tools Required, Shoulder Strap Assembly, To Relocate Shoulder Strap Clamp

Page 10

ASSEMBLY

WARNING: If received assembled, review all assembly steps to ensure your unit is properly assembled and all fasteners are secure.

Examine parts for damage. Do not use dam- aged parts.

NOTE: If you need assistance or find parts missing or damaged, call 1-800-554-6723.

TOOLS REQUIRED

SHex wrench

SChain adjustment tool (bar tool)

INSTALLING PRUNER OR LINE TRIMMER ATTACHMENT CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Coupler

LOOSEN

TIGHTEN Knob

2.Remove the shaft cap from attachment (if present).

3.Position locking/release button of attach- ment into guide recess of coupler.

4.Push the attachment into the coupler until the locking/release button snaps into the primary hole.

5.Before using the unit, tighten the knob se- curely by turning clockwise.

Coupler Primary Hole

Guide Recess

Upper Locking/ Lower

Shaft Release Attachment

Button

WARNING: Make sure the locking/ release button is locked in the primary hole and the knob is securely tightened before op- erating the unit. All attachments are designed to be used in the primary hole.

For optional attachments, see the AS- SEMBLY section of the applicable attach- ment instruction manual.

SHOULDER STRAP ASSEMBLY

WARNING: Proper shoulder strap adjustments must be made with the motor completely stopped before using unit.

1.Try on shoulder strap and adjust for fit and balance before starting the unit or begin- ning a cutting operation.

2.Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is centered on your back and the hook is

to the right side of your waist.

NOTE: A one-half twist is built in the shoul- der strap to allow the strap to rest flat on the shoulder.

3.Adjust the strap, allowing the hook to be about 3 -- 6 inches (8 -- 15 cm) below the waist.

4.Fasten the strap hook to the clamp lo- cated between the trigger handle and the assist handle and lift the tool to the operat-

ing position.

NOTE: It may be necessary to relocate the shoulder strap clamp on the shaft for proper balancing of unit.

TO RELOCATE SHOULDER STRAP CLAMP:

1.Loosen and remove both clamp screws.

2.Place the upper shoulder strap clamp over the upper shaft.

3.Position the lower shoulder strap clamp under the upper shaft and align the upper and lower clamp screw holes.

Upper Shoulder

Strap Clamp

POWERHEAD

END

Lower Shoulder

ATTACHMENT

END

Strap Clamp

 

Screws

4.Insert two screws into the screw holes.

5.Secure shoulder strap clamp by tighten- ing screws with a hex wrench.

ADJUSTING THE ASSIST HANDLE

WARNING: When adjusting the assist handle during pruner use, be sure it remains be-

tween the coupler and the lower arrow (closest to coupler) on the safety label to ensure proper balancing of unit. When adjusting the assist handle during use of optional attach- ments (or handlebar for edger attachment), it must be repositioned between the trigger switch

and the

upper arrow (closest to motor) on

the safety label.

1.Loosen wing nut on handle.

2.Rotate the handle on the shaft to an up- right position; retighten wing nut.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual de Instrucciones Manuel d’Instructions Is necessary when used near children Identification of SymbolsSafety Rules Plan AheadPlosive vapors can build up Electrical Safety applies to all attachmentsUse a voltage supply as shown on unit Do not use multiple cordsKickback Pruner SafetyRotational Kickback can occur when Reduce the Chance Kickback Kickback Safety FeaturesLine Trimmer Safety Maintain ControlMaintain Your Unit in Good Working Order Transporting and StorageRecommended Attachments Blower SafetyCultivator Safety For Optional AttachmentsPruner Safety Reciprocating Blade Edger SafetyVacuum Safety On the attachmentSnow Thrower Safety Hedge Trimmer SafetyHigh speed causing injury Adjusting the Assist Handle AssemblyShoulder Strap Assembly Tools RequiredOperation Attach the Extension Cord to Your Unit Installing Optional ATTACH- MentsInstalling Attachment Hanger Before Starting UnitSize limbs or slender material Pruning Important PointsPruning Technique FootRightWrong Trimmer Line AdvanceCutting Methods TrimmingMaintenance Service and Adjustments Replacing the Line Chain AdjustmentUser Replaceable Service Parts Seasonal StorageTroubleshooting Table Cause Remedy Limited Warranty

810 EPT specifications

The Poulan 810 EPT is a high-performance chainsaw designed for both professional loggers and home landscaping enthusiasts alike. Known for its reliability and durability, this model stands out due to its advanced features and cutting-edge technology.

At the heart of the Poulan 810 EPT is a powerful 81cc, two-stroke engine. This robust engine delivers significant power for cutting through tough wood, making it suitable for heavy-duty tasks. With a guide bar length of up to 20 inches, it provides the ability to tackle big jobs efficiently. The chainsaw’s high speed allows for faster cutting, which is particularly beneficial for clearing trees or trimming large branches.

One of the key features of the Poulan 810 EPT is its EPT (Easy Pull Technology). This innovative system significantly reduces the effort needed to start the engine. It incorporates a spring-assisted starter that makes pull starts smoother and less strenuous. As a result, users can enjoy quicker and easier startups, which is especially advantageous during prolonged use.

Another notable aspect of the Poulan 810 EPT is its anti-vibration technology. This feature minimizes the vibrations felt by the user, leading to increased comfort during operation, even during extended tasks. Prolonged use can be taxing on the hands, but with this technology in place, users can maintain better control and reduce fatigue.

The chainsaw also comes equipped with a tool-less chain tensioning system, allowing for quick and easy adjustments on-the-go. This means that users can tighten or loosen the chain without the need for additional tools, ensuring optimal performance and safety during operation. The chain itself is designed for superior cutting efficiency and is specifically crafted to maintain sharpness for longer periods.

Safety is paramount in chainsaw design, and the Poulan 810 EPT incorporates several safety features. It includes a chain brake that engages instantly to prevent kickback injuries, as well as a throttle lockout to avoid accidental starts. These features are crucial for enhancing user safety while operating the machine.

Overall, the Poulan 810 EPT stands out as a powerful, efficient, and user-friendly chainsaw. With its advanced engine technology, ease of use features, and safety mechanisms, it is an ideal option for those seeking a reliable tool for both professional and personal woodcutting tasks.
Top Page Image Contents