Poulan 810 EPT instruction manual Service and Adjustments

Page 16

BAR MAINTENANCE

If your pruner cuts to one side, has to be forced through the cut, or been run with an im- proper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. After each use, with unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SDisconnect pruner from power source.

S Loosen and remove bar clamp nut and chain brake. Remove bar and chain from pruner.

S Clean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replace- ment is necessary, use only the guide bar speci- fied for your pruner in the repair parts list.

LUBRICATION

Bar Oil

Fill Cap

SSee GUIDE BAR AND CHAIN OIL under the OPERATION section.

SERVICE AND ADJUSTMENTS

WARNING: Disconnect unit from power source before performing service or making adjustments.

CHAIN SHARPENING

Chain sharpening is a complicated task that requires special tools. We recommended you refer chain sharpening to a professional chain sharpener.

CHAIN REPLACEMENT

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

It is normal for a new chain to stretch during the first 15 minutes of operation. You should re- check your chain tension frequently and adjust the chain tension as required. See CHAIN TEN- SION section.

Replace the old chain when it becomes worn or damaged. Use only the Low-Kickback replace- ment chain specified in the repair parts list.

TO REPLACE CHAIN:

1.Disconnect pruner from power source.

2.Remove bar clamp nut.

3.Remove bar clamp.

4.Turn adjusting screw by hand counter- clockwise until adjusting pin just touches the stop.

5.Slide guide bar behind sprocket until guide bar stops against sprocket.

6.Remove the old chain.

7.Carefully remove new chain from pack- age. Hold chain with the drive links as shown.

Cutter

Tip of

Bar

Drivelink

CUTTERS MUST FACE IN

DIRECTION OF ROTATION

Cutters

Depth Gauge

Drive Links

8.Place chain over sprocket, fitting the drive links in the sprocket.

9.Fit bottom of drive links between the teeth in the sprocket in the nose of the guide bar.

10.Fit chain drive links into bar groove.

11.Pull guide bar forward until chain is snug in guide bar groove. Ensure all drive links are in the bar groove.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual de Instrucciones Manuel d’Instructions Identification of Symbols Safety RulesIs necessary when used near children Plan AheadElectrical Safety applies to all attachments Use a voltage supply as shown on unitPlosive vapors can build up Do not use multiple cordsKickback Pruner SafetyRotational Kickback can occur when Kickback Safety Features Line Trimmer SafetyReduce the Chance Kickback Maintain ControlMaintain Your Unit in Good Working Order Transporting and StorageBlower Safety Cultivator SafetyRecommended Attachments For Optional AttachmentsEdger Safety Vacuum SafetyPruner Safety Reciprocating Blade On the attachmentSnow Thrower Safety Hedge Trimmer SafetyHigh speed causing injury Assembly Shoulder Strap AssemblyAdjusting the Assist Handle Tools RequiredOperation Installing Optional ATTACH- Ments Installing Attachment HangerAttach the Extension Cord to Your Unit Before Starting UnitPruning Important Points Pruning TechniqueSize limbs or slender material FootTrimmer Line Advance Cutting MethodsRightWrong TrimmingMaintenance Service and Adjustments Chain Adjustment User Replaceable Service PartsReplacing the Line Seasonal StorageTroubleshooting Table Cause Remedy Limited Warranty

810 EPT specifications

The Poulan 810 EPT is a high-performance chainsaw designed for both professional loggers and home landscaping enthusiasts alike. Known for its reliability and durability, this model stands out due to its advanced features and cutting-edge technology.

At the heart of the Poulan 810 EPT is a powerful 81cc, two-stroke engine. This robust engine delivers significant power for cutting through tough wood, making it suitable for heavy-duty tasks. With a guide bar length of up to 20 inches, it provides the ability to tackle big jobs efficiently. The chainsaw’s high speed allows for faster cutting, which is particularly beneficial for clearing trees or trimming large branches.

One of the key features of the Poulan 810 EPT is its EPT (Easy Pull Technology). This innovative system significantly reduces the effort needed to start the engine. It incorporates a spring-assisted starter that makes pull starts smoother and less strenuous. As a result, users can enjoy quicker and easier startups, which is especially advantageous during prolonged use.

Another notable aspect of the Poulan 810 EPT is its anti-vibration technology. This feature minimizes the vibrations felt by the user, leading to increased comfort during operation, even during extended tasks. Prolonged use can be taxing on the hands, but with this technology in place, users can maintain better control and reduce fatigue.

The chainsaw also comes equipped with a tool-less chain tensioning system, allowing for quick and easy adjustments on-the-go. This means that users can tighten or loosen the chain without the need for additional tools, ensuring optimal performance and safety during operation. The chain itself is designed for superior cutting efficiency and is specifically crafted to maintain sharpness for longer periods.

Safety is paramount in chainsaw design, and the Poulan 810 EPT incorporates several safety features. It includes a chain brake that engages instantly to prevent kickback injuries, as well as a throttle lockout to avoid accidental starts. These features are crucial for enhancing user safety while operating the machine.

Overall, the Poulan 810 EPT stands out as a powerful, efficient, and user-friendly chainsaw. With its advanced engine technology, ease of use features, and safety mechanisms, it is an ideal option for those seeking a reliable tool for both professional and personal woodcutting tasks.
Top Page Image Contents