Poulan 530088847 Attaching the Control Handle to the Handlebar, Configuring Your Unit

Page 5

S Insert screws and hand tighten only. These

screws will be tightened later.

Bracket Cover

 

 

 

 

Screw

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mounting

 

 

 

 

 

Handlebar

 

 

 

 

 

 

 

 

 

Bracket

 

 

 

 

 

ATTACHING THE CONTROL HANDLE TO THE HANDLEBAR

NOTE: Make sure the wire going to the con- trol handle is routed below the tube and re- mains on the right side of the handlebar and the tube.

SRemove screw from control handle. Screw

SInsert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.

NOTE: A one-half twist is built in the shoulder strap to allow the strap to rest flat on the shoul- der.

S Adjust the strap, allowing the hook to be about 6 inches below the waist.

SFasten the strap hook to the clamp located between the foam grip and the mounting block and lift the tool to the operating posi- tion.

CONFIGURING YOUR UNIT

You can configure your unit using a cutting head for grass and light weeds, or a brush blade for cutting saplings and similar size ma- terial. Go to the section for the desired configuration and follow the instructions for assembling your unit.

ASSEMBLY INFORMATION -

TRIMMER HEAD

Screw Hole

SSlide handle onto the right side of the han-

dlebar and align the screw hole.

SRe-insert screw and tighten securely. NOTE: Make sure the control handle is on the right side of the unit as shown in the il- lustration below, and the On/Stop switch is lo- cated on the top of the control handle.

S Adjust the handlebar to the proper position and tighten the two screws you left loose during handlebar assembly. Make sure these screws are securely tightened.

S After attaching the control handle and tight- ening the handlebar, route the wire from the control handle through the slit in the bottom of the foam grip.

Foam Grip

TRIMMER

HEAD

NOTE: If your unit has been assembled for brush blade use, refer to the section AS-

SEMBLY INFORMATION FOR USING YOUR UNIT WITH A BRUSHBLADE and re- verse the steps to remove the metal shield and blade before you mount the plastic shield and trimmer head.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

Slit Wire

ASSEMBLY OF SHOULDER STRAP

WARNING: Proper shoulder strap and handlebar adjustments before starting the en- gine are required.

STry on shoulder strap and adjust for fit and bal- ance before starting the engine or beginning a cutting operation.

5

WARNING: The shield must be prop- erly installed. The shield provides partial protec- tion from the risk of thrown objects to the opera- tor and others and is equipped with a line limiter which cuts excess line to the proper length. The line limiter (on underside of shield) is sharp and can cut you.

SRemove wing nut from shield.

SInsert bracket into slot on shield.

SPivot shield until bolt passes through hole in bracket.

STighten the wing nut securely.

SIf your unit has a plastic cover over the threads on the threaded shaft, remove the covering to expose the threads.

Page 4 Page 6
Image 5
Page 4 Page 6
Contents URL Always Wear Operator SafetyEye ProtectionFuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageAssembly Tools Required Carton ContentsAttaching the Tube Attaching the HandlebarAssembly Information Trimmer Head Configuring Your UnitAssembly of Shoulder Strap Attaching the Control Handle to the HandlebarAssembly of the Metal Shield Assembly Information Brush BladeAssembly of the Metal Blade Brush BladeStarting Your Engine HOW to Stop Your UnitON/STOP StopStarting a Warm Engine Operating PositionOperating Instructions for USE with Trimmer Head Advancing the Trimmer LineReplacing the Line Operating Instructions for USE with Brush BladeOr others Use the shoulder strap and keep a firm gripCarburetor Adjustment Spool ReplacementSpark Plug Ignition TimingHead Use only 0.080 2 mm dia. line Troubleshooting Table Cause RemedySee Carburetor Adjustments Replacement of any warranted part will be Coverage This warranty shall be for aMaintenance of your lawn and garden Abuse, neglect, or improper maintenance are

530088847 specifications

The Poulan 530088847 is an effective and versatile replacement part designed to enhance the performance of your Poulan chainsaw. This component is primarily recognized as an air filter, playing a pivotal role in maintaining the engine’s efficiency and longevity. By ensuring that the air entering the combustion chamber is free from dust, debris, and contaminants, the 530088847 filter promotes optimal engine performance and fuels combustion efficiently.

One of the main features of the Poulan 530088847 is its high-quality filtration capability. The filter is built to capture even the smallest particles, preventing them from entering the engine. This is crucial because dirt and debris can cause considerable damage to the engine over time, leading to reduced performance and potential malfunctions. By using this premium air filter, chainsaw users can enjoy a longer lifespan for their equipment and maintain consistent cutting power.

Another significant characteristic of the Poulan 530088847 is its ease of installation. Designed with the user in mind, this part can be replaced quickly without the need for specialized tools or extensive mechanical knowledge. This user-friendly nature is especially beneficial for individuals who rely heavily on their chainsaws and cannot afford downtime.

Furthermore, the Poulan 530088847 is compatible with a variety of Poulan chainsaw models, making it a versatile option for many users. This compatibility ensures that individuals can find a suitable replacement for their existing air filter, further solidifying the product’s appeal within the chainsaw community.

The materials used in the construction of the Poulan 530088847 are durable and designed to withstand the rigors of outdoor usage. This resilience serves to not only extend the service life of the filter itself but also to enhance the overall reliability of the chainsaw.

Overall, the Poulan 530088847 stands out as a crucial component for maintaining the health and performance of Poulan chainsaws. Its exceptional filtration capabilities, ease of installation, compatibility, and robust construction make it an essential part for any chainsaw owner looking to optimize their equipment's performance. By investing in the 530088847 air filter, users can ensure they achieve the best possible results from their chainsaw while minimizing potential engine issues.
Top Page Image Contents