Poulan 530088847 Assembly Information Brush Blade, Assembly of the Metal Shield

Page 6

S Before installing the trimmer head, make sure the dust cup and retaining washer are positioned on the gearbox as shown below.

 

Bracket

Slot

Wing Nut

 

DANGER: The metal shield must be properly installed on the tool anytime the tool is used with the blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by- standers. Failure to install the shield in the position shown can result in serious injury to

Shield

Gearbox

the operator. The length of the shield must be aligned with the length of the tube. The blade is sharp and can cut you. Be sure to wear gloves while working with blades.

S If your unit has a plastic cover over the threads on the shaft, remove the covering to

Dust Cup

Retaining Washer

NOTE: Make sure all parts are properly installed as illustrated in the illustration before installing the trimmer head.

SAlign hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

SInsert a hex wrench into aligned holes. This will keep the shaft from turning while tighten- ing the trimmer head.

Hex Wrench

S While holding the hex wrench in position, thread trimmer head onto the shaft and tight- en until secure.

NOTE: The retaining washer must be posi- tioned with the raised section facing toward the gearbox.

ASSEMBLY INFORMATION -

BRUSH BLADE

BRUSH

BLADE

NOTE: If your unit has been assembled for trimmer head use, refer to the section ATTACH-

ING THE PLASTIC SHIELD AND TRIMMER HEAD and reverse the steps to remove the plas- tic shield and trimmer head before you mount the metal shield and blade. Store these parts for fu- ture use. Never use the trimmer head with the metal blade installed.

ASSEMBLY OF THE METAL SHIELD

6

expose the threads.

S Place the metal shield under the gearbox, and align the screw holes.

Gearbox

Shield

S Insert the 4 mounting screws through the bottom of the shield. Thread them into the gearbox. Tighten evenly and securely with one of the hex key wrenches provided.

ASSEMBLY OF THE METAL BLADE

WARNING: Do not use any blades, or fastening hardware other than the washers and nuts illustrated in the following illustrations. These parts must be provided by Poulan/Weed Eater and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others.

NOTE: When installing the blade, make sure you install it with the correct side facing up (marked on the blade). If you are re-installing an older blade and the writing has worn off, use the following illustration as a guide.

Top view of blade

Teeth on blade point in this direction

NOTE: The dust cup and retaining washer are located on the gearbox and not in the parts bag.

SRemove the retainer washer from the gear- box, and leave the dust cup on the gearbox. NOTE: It may be necessary to remove a

Page 5 Page 7
Image 6
Page 5 Page 7
Contents URL Eye Operator SafetyAlways Wear ProtectionCutting Safety UNIT/MAINTENANCE SafetyFuel Safety Transporting and StorageAttaching the Tube Carton ContentsAssembly Tools Required Attaching the HandlebarAssembly of Shoulder Strap Configuring Your UnitAssembly Information Trimmer Head Attaching the Control Handle to the HandlebarAssembly of the Metal Blade Assembly Information Brush BladeAssembly of the Metal Shield Brush BladeON/STOP HOW to Stop Your UnitStarting Your Engine StopOperating Instructions for USE with Trimmer Head Operating PositionStarting a Warm Engine Advancing the Trimmer LineOr others Operating Instructions for USE with Brush BladeReplacing the Line Use the shoulder strap and keep a firm gripSpark Plug Spool ReplacementCarburetor Adjustment Ignition TimingTroubleshooting Table Cause Remedy See Carburetor AdjustmentsHead Use only 0.080 2 mm dia. line Maintenance of your lawn and garden Coverage This warranty shall be for aReplacement of any warranted part will be Abuse, neglect, or improper maintenance are

530088847 specifications

The Poulan 530088847 is an effective and versatile replacement part designed to enhance the performance of your Poulan chainsaw. This component is primarily recognized as an air filter, playing a pivotal role in maintaining the engine’s efficiency and longevity. By ensuring that the air entering the combustion chamber is free from dust, debris, and contaminants, the 530088847 filter promotes optimal engine performance and fuels combustion efficiently.

One of the main features of the Poulan 530088847 is its high-quality filtration capability. The filter is built to capture even the smallest particles, preventing them from entering the engine. This is crucial because dirt and debris can cause considerable damage to the engine over time, leading to reduced performance and potential malfunctions. By using this premium air filter, chainsaw users can enjoy a longer lifespan for their equipment and maintain consistent cutting power.

Another significant characteristic of the Poulan 530088847 is its ease of installation. Designed with the user in mind, this part can be replaced quickly without the need for specialized tools or extensive mechanical knowledge. This user-friendly nature is especially beneficial for individuals who rely heavily on their chainsaws and cannot afford downtime.

Furthermore, the Poulan 530088847 is compatible with a variety of Poulan chainsaw models, making it a versatile option for many users. This compatibility ensures that individuals can find a suitable replacement for their existing air filter, further solidifying the product’s appeal within the chainsaw community.

The materials used in the construction of the Poulan 530088847 are durable and designed to withstand the rigors of outdoor usage. This resilience serves to not only extend the service life of the filter itself but also to enhance the overall reliability of the chainsaw.

Overall, the Poulan 530088847 stands out as a crucial component for maintaining the health and performance of Poulan chainsaws. Its exceptional filtration capabilities, ease of installation, compatibility, and robust construction make it an essential part for any chainsaw owner looking to optimize their equipment's performance. By investing in the 530088847 air filter, users can ensure they achieve the best possible results from their chainsaw while minimizing potential engine issues.
Top Page Image Contents