Service and Adjustments, BAR Maintenance | Poulan 115260526 instruction

BAR MAINTENANCE

If your pruner cuts to one side, has to be forced through the cut, or been run with an im- proper amount of bar lubrication it may be necessary to service your bar. A worn bar will damage your chain and make cutting difficult. After each use, with unit disconnected from power source, clean all sawdust from the guide bar and sprocket hole.

To maintain guide bar:

SDisconnect pruner from power source.

S Loosen and remove bar clamp nut and chain brake. Remove bar and chain from pruner.

S Clean the oil holes and bar groove after each 5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

S Burring of guide bar rails is a normal process of rail wear. Remove these burrs with a flat file.

SWhen rail top is uneven, use a flat file to re- store square edges and sides.

File Rail Edges

and Sides

Square

Worn Groove

Correct Groove

Replace guide bar when the groove is worn, the guide bar is bent or cracked, or when excess heating or burring of the rails occurs. If replace- ment is necessary, use only the guide bar speci- fied for your pruner in the repair parts list.

LUBRICATION

Bar Oil

Fill Cap

SSee GUIDE BAR AND CHAIN OIL under the OPERATION section.

SERVICE AND ADJUSTMENTS

WARNING: Disconnect unit from power source before performing service or making adjustments.

File Holder

File

CHAIN SHARPENING

Cutter

90˚

Improper chain sharpening techniques and/or depth gauge maintenance will increase the chance of kickback which can result in serious injury.Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

Conditions which indicate the need for chain sharpening:

SReduction in size of wood chips. The size of the wood chip will decrease as the chain gets duller until it becomes more like a pow- der than a chip. Note that dead or rotted wood will not produce a good chip.

SSaw cuts to one side or at an angle. S Saw has to be forced through the cut.

Tools required:

S3/16 inch (4,5 mm) diameter round file and

file holder

SFlat file

SDepth gauge tool

TO SHARPEN CHAIN:

1.Disconnect pruner from power source.

2.Check chain for proper tension. Adjust chain tension if necessary. See CHECK CHAIN TENSION section.

3.Sharpen cutters.

STo sharpen the cutters, position the file holder level (90˚) so that it rests on the top edges of the cutter and depth gauge.

NOTE: The chain has both left and right hand cutters.

Depth Gauge

SAlign the 30˚ file holder marks parallel with the bar and to the center of the chain.

Cutter

30˚ Cutter

File Holder Line

SSharpen cutters on one side of the chain first. File from the inside of each cutter to the outside. Then, turn the chain saw around and repeat the process for the

other side of the chain.

SFile on the forward stroke only. Use 2

or 3 strokes per cutting edge.

SKeep all cutters the same length when

filing.

SFile enough to remove any damage to cutting edges (side plate and top plate of cutter).

All Cutters	Remove Damage
Same Length
	Top Plate
	Side Plate

SFile chain to meet the specifications as shown.

115260526 specifications

The Poulan 115260526 is a versatile chainsaw that has gained popularity among both amateur and professional users for its reliability and performance. This model is designed for a variety of cutting tasks, ranging from trimming branches to felling trees. It combines a powerful engine with innovative features, making it an ideal choice for homeowners and landscapers alike.

One of the standout characteristics of the Poulan 115260526 is its robust engine. The chainsaw is equipped with a 25cc, 2-stroke engine that delivers impressive power for its class. This efficient engine enables users to tackle demanding cutting chores without experiencing unnecessary fatigue. Additionally, the lightweight design of the chainsaw makes it easier to maneuver and reduces the strain on the operator during extended use.

Another key feature of the Poulan 115260526 is its Easy Start technology. This intuitive starting system reduces the effort required to start the engine, allowing users to get to work quickly without the hassle of traditional pull-start systems. The reduced resistance in the starting mechanism enhances user experience, making it suitable for those who may be less experienced with chainsaws.

Safety is always a concern when using power tools, and the Poulan 115260526 addresses this with several built-in safety features. It comes equipped with a chain brake that activates when a kickback occurs, stopping the chain instantly to reduce the risk of injury. The chainsaw also features a hand guard to protect the user’s hands while operating.

The chainsaw's cutting capability is further enhanced by its Oregon chain and bar system. The 16-inch bar length paired with a high-quality chain ensures smooth and swift cutting, allowing users to tackle tougher wood with confidence. The automatic oiling system helps maintain the chain’s performance by delivering oil to the bar and chain during operation, thus extending the life of the components.

In terms of maintenance, the Poulan 115260526 is designed for easy access to critical parts, ensuring that users can swiftly perform routine checks and repairs. This practicality contributes to the chainsaw’s longevity and reliability over time.

In summary, the Poulan 115260526 stands out for its powerful yet lightweight design, user-friendly starting technology, safety features, and efficient cutting performance. These attributes make it a valuable tool for anyone looking to maintain their property or engage in landscaping projects. With the right care and maintenance, this chainsaw is sure to deliver exceptional results for years to come.