Homelite UT20024A manual String Replacement, Cleaning the Exhaust Port and Muffler Spark Arrestor

Page 15

MAINTENANCE

To install the spool retainer:

Turn the spool retainer clockwise for Trimlite and Trim ’n Edge.

SPRING

SPOOL

Turn the spool retainer counterclockwise for Easy Reach.

nPull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head.

STRING REPLACEMENT

See Figures 16 - 19.

nStop the engine and disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for Trimlite and Trim ’n Edge.

Turn the spool retainer clockwise for Easy Reach.

nRemove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool.

nCut two pieces of string, each being approximately 9 ft. (2.7 m) long. Use only .080 in. (2.0 mm) diameter mono- filament string.

nInsert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool.

nRepeat above step with second string, using the bottom part of spool. Do not overfill.

nReplace the spool and the spool retainer. Refer to “Spool Replacement” earlier in this manual.

CLEANING THE EXHAUST PORT AND MUFFLER

NOTE: Depending on the type of fuel used, the type and amount of oil used, and/or your operating conditions, the exhaust port and muffler may become blocked with carbon deposits. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance. We highly recommended that only qualified service technicians perform this service.

SPARK ARRESTOR

The muffler is equipped with a spark arrestor (screen inside the muffler body). Through normal use, the screen can be- come dirty and should be periodically cleaned or replaced by an anthorized service dealer.

ARROWS ON

SPOOL

ANCHOR

HOLE

FIRST STRING

Fig. 16

 

FIRST

STRING

SLOT

Fig. 17

SECOND

STRING

 

Fig. 18

SLOT

ARROWS ON

 

SPOOL

Fig. 19

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules Specific Safety Rules for Trimmer USESymbol Name Explanation SymbolsService Features Trimlite ModelTrim ‘N Edge Model Grass Deflector Easy Reach ModelsKnow Your String Trimmer Ergonomic DesignFront Handle AssemblyUnpacking Packing ListSee Figures 5 Wing NUT Lock Washer Edger Guide Pieces Flat Short BoltWing NUT Operation Straight Shaft Grass Deflector Easy ReachFueling and Refueling the Trimmer Fuel Mixture Operating the Trimmer Filling TankTo Stop the Engine If Assistance is Required for this ProductTrimlite and Trim ‘N Edge Advancing String Using the EZ Line TAP Advance SystemAdvancing the String Manually CUT OFF BladeEdger Guide Operation Trim ‘N Edge only See Figures 12Wing NUT Edger Guide Maintenance General MaintenanceSee Figures 14 See Figures 16 String ReplacementCleaning the Exhaust Port and Muffler Spark Arrestor Spring SpoolStoring the Trimmer 1 Month or Longer Replacing and Cleaning AIR FilterFuel CAP Spark PlugProblem Possible Cause Solution TroubleshootingIdle Speed Screw Limited Warranty Statement WarrantyMANUFACTURER’S Warranty Coverage This Product WAS Manufactured with a Catalyst Muffler California Proposition Trimlite UT20004A Trim ‘n Edge UT20024A Easy Reach UT20044A
Top Page Image Contents