Husqvarna SMC 50 EF manual Setting up the Saw Carriage FIG, Saw Carriage Adjustment FIG

Page 17

INSTALLATION

Setting up the Saw Carriage (FIG. 24)

!WARNING!

The saw carriage is heavy. Two persons are required when setting up. Always wear boots with steel toecaps.

CAUTION!

Do not drop the saw carriage onto the rails or any other hard surface too heavily. This will result in permanent damage to the saw carriage’s bearings.

Do not place the saw carriage directly on the ground so that dirt and unnecessary con- tamination can come into contact with the saw carriage’s wheels.

Place the saw carriage on the rails and make adjustments as follows:

1.Two persons take hold of the saw carriage, one on each side. Hold the saw carriage as follows: The right-hand side: under the engine console (A) on the electric sawmill or under the saddle on the chain saw sawmill. The left-hand side: in the sawmill chassis (B).

2.Lift and place the saw carriage so that the grooves in its wheels are positioned above their respective rails (FIG. 25). Carefully lower the saw carriage onto the rails.

FIG. 24

B

A

FIG. 25

Saw Carriage Adjustment (FIG. 26)

The saw carriage is aligned on the rails by fitting its lower guide wheels and rail guards. The lower guide bearings have the task of preventing the saw carriage from tilting and the rail guards keep the rails and the saw carriage’s wheels free from dirt and the like. Assembled on the saw carriage are:

•Two lower guide wheels

•Four rail guards.

Assembly is done as follows:

1.Fix the guide wheel’s bracket in place with a screw. Place a 0.2 mm feeler gauge between the bearing and rail (FIG. 26).

2.Press the bearing against the rail and tighten the bearing bracket screw. Tightening torque: 40-50 Nm. Now remove the feeler gauge.

3.Carry out 1-2 above for the remaining guide wheels.

4.Position the four rail guards (FIG. 27) above the wheel.

FIG. 26

0,2 mm

FIG. 27

English – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents English SMC 50 SMC 50 E SMC 50 EFTable of Contents Introduction IntroductionSymbols KEY to SymbolsPersonal Protective Equipment Safety RegulationsSafety Regulations Fuel Safety One-man Sawmill Safety EquipmentSafety During Use Risk ZoneOne-man sawmill chain saw engine DescriptionOne-man Sawmill Electric Motor One-man sawmill with electric motor and feed Saw carriage FIG Height Setting FIGFrame and FIG Handlebars FIGVibration damping plate for the chain saw FIG Chain oil tank FIGBar and chain FIG Feed unit for chain sawmill with electric motor FIGChain saw engine FIG MotorsElectric Motor FIG Electric motor feed unit FIGRails Height Adjustment BLog Bolsters a Folding Stops CRail Guard Adjustable Support FeetRail Stop Safety Devices Installation InstallationInstallation Site UnpackingSaw Carriage Adjustment FIG Setting up the Saw Carriage FIGInstall the bar FIG Install chain saw and bar FIGOne-man sawmill with chain saw engine One-man sawmill with electric motorInstall throttle and cable FIG Install scale pointer and scale FIGInstall the handlebar FIG Checking the bar Adjusting the barPetrol Fuel HandlingFuel chain saw engine Fuelling Two-stroke oilMixing Stopping the chain saw engine FIG Starting and StoppingStarting a cold chain saw engine FIG Starting the electric sawmill with feed FIG Starting the electric sawmill FIGSecuring the Log USESawing Calculating the YieldStarting the Electric Motor Starting the Petrol EngineEdging FIG Clutch drum MaintenanceSaw chain Drive belt Saw unit’s height adjustmentDaily maintenance MaintenanceWeekly maintenance Monthly maintenanceTechnical data Technical DataEU Declaration of Conformity only applies to Europe Noise LevelsVibration Levels Page 2004W12 114 02
Top Page Image Contents