Husqvarna SMC 50 EF manual Noise Levels, Vibration Levels

Page 34

TECHNICAL DATA

Noise Levels

 

 

Equivalent noise intensity at operator’s ear during

 

 

sawing, measured according to ISO 7917, dB(A)

 

 

Petrol engine:

104,9

 

Electric motor:

89,8

 

Equivalent noise level measured according to EN

 

 

1807 and ISO 7960, dB(A)

 

 

Petrol engine:

112,9

 

Electric motor:

102,3

 

Vibration Levels

 

 

Vibration level in the handle, during sawing,

 

 

according to international standards, m/s2

Left

Right

Petrol engine:

5

5

Electric motor:

1,8

1,8

EU Declaration of Conformity (only applies to Europe)

Directive 98/37/EC, Appendix 2 A

Lennartsfors AB, Lennartsfors 1, SE-672 92 ÅRJÄNG, hereby guarantees that the one-man sawmills Husqvarna SMC 50 and SMC 50 E, SMC 50 EF, with serial numbers 02 100001 – 02 5200100, meet the standards prescribed in the COUNCIL’S DIRECTIVES:

-of 22 June 1998 ”relating to machinery” 98/37/EC, appendix IIA.

-of 3 May 1989 ”relating to electromagnetic compatibility” 89/336/EEC, and applicable supplements.

-of 19 February 1973 ”relating to electrical equipment”, 73/23/EEC.

For information regarding noise emissions, see the Technical Data chapter.

The following harmonised standards have been applied: EN292-1, EN 60204:1.

SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out voluntary type approval for Lennartsfors AB. The certificates are numbered: SEC/95/248 – SMC 50 and SEC/95/249 – SMC 50 E, SMC 50 EF. The supplied one-man sawmill conforms with the example that underwent EU type approval.

Årjäng, 23 October 2003

Örjan Gustafsson, Product Manager, Lennartsfors AB

34 – English´®z+H7¶6_¨

Page 33 Page 35
Image 34
Page 33 Page 35
Contents SMC 50 SMC 50 E SMC 50 EF EnglishTable of Contents Introduction IntroductionKEY to Symbols SymbolsSafety Regulations Safety RegulationsPersonal Protective Equipment Safety During Use One-man Sawmill Safety EquipmentFuel Safety Risk ZoneDescription One-man sawmill chain saw engineOne-man Sawmill Electric Motor One-man sawmill with electric motor and feed Frame and FIG Height Setting FIGSaw carriage FIG Handlebars FIGBar and chain FIG Chain oil tank FIGVibration damping plate for the chain saw FIG Feed unit for chain sawmill with electric motor FIGElectric Motor FIG MotorsChain saw engine FIG Electric motor feed unit FIGLog Bolsters a Height Adjustment BRails Folding Stops CRail Stop Adjustable Support FeetRail Guard Safety Devices Installation Site InstallationInstallation UnpackingSetting up the Saw Carriage FIG Saw Carriage Adjustment FIGOne-man sawmill with chain saw engine Install chain saw and bar FIGInstall the bar FIG One-man sawmill with electric motorInstall the handlebar FIG Install scale pointer and scale FIGInstall throttle and cable FIG Adjusting the bar Checking the barFuel chain saw engine Fuel HandlingPetrol Mixing Two-stroke oilFuelling Starting a cold chain saw engine FIG Starting and StoppingStopping the chain saw engine FIG Starting the electric sawmill FIG Starting the electric sawmill with feed FIGUSE Securing the LogCalculating the Yield SawingStarting the Petrol Engine Starting the Electric MotorEdging FIG Maintenance Clutch drumSaw chain Saw unit’s height adjustment Drive beltWeekly maintenance MaintenanceDaily maintenance Monthly maintenanceTechnical Data Technical dataVibration Levels Noise LevelsEU Declaration of Conformity only applies to Europe Page 114 02 2004W12
Top Page Image Contents