Husqvarna SMC 50 E Starting the electric sawmill FIG, Starting the electric sawmill with feed FIG

Page 24

STARTING AND STOPPING

Starting the electric sawmill (FIG. 41)

!WARNING

The sawmill must not be started until the appropriate current and voltage have been connected. Use suitable personnel trained in the country in question.

NOTE! The first time the sawmill is started or when it has been moved to another power outlet:

•Test start the sawmill in accordance with the starting instructions.

•Check the chain direction. If the chain runs in the wrong direction, there is a phase inverter on the power connector (FIG. 40). The phase is inverted with the aid of a screwdriver, as illustrated in FIG. 40.

1.Check that the power cable is connected correctly.

2.Keep the green start button (29) pressed in using your left hand. Now press in the start/stop handle

(B) with your right hand and the sawmill will start. The sawmill stops as soon as the handle is not activated. The sawmill can also be stopped using the red stop button (32).

3.Check the chain direction, see FIG. 29.

Starting the electric sawmill with feed (FIG. 42)

1.Check that the power cable is connected correctly.

2.Keep the green start button (29) pressed in using your right hand. Then press the black safety switch (37) using your left hand. When the sawmill has started, the safety switch must be held in during sawing.

3.Start feeding with the white start button (30) using your right hand. Ensure that the control (31) is in position ”0”.

4.Then increase the speed with the variable control so that the saw carriage starts moving. Then adjust to the desired feed speed. CAUTION! There is variable adjustment for feeding, so overloading is possible depending on the width of the saw cut. In the event of overloading, the current to the saw motor is broken.

5.The sawmill stops as soon as the safety switch is not activated.

6.Return feeding is started with the white start button (30) and the speed is controlled with the variable control. Return feeding only starts when the saw motor is switched off.

FIG. 40

FIG. 41

B

 

32

29 37

A

 

27

 

16

 

FIG. 42

30

29

31

37

27

24 – English

Page 23 Page 25
Image 24
Page 23 Page 25
Contents SMC 50 SMC 50 E SMC 50 EF EnglishTable of Contents Introduction IntroductionKEY to Symbols SymbolsSafety Regulations Safety RegulationsPersonal Protective Equipment One-man Sawmill Safety Equipment Fuel SafetySafety During Use Risk ZoneDescription One-man sawmill chain saw engineOne-man Sawmill Electric Motor One-man sawmill with electric motor and feed Height Setting FIG Saw carriage FIGFrame and FIG Handlebars FIGChain oil tank FIG Vibration damping plate for the chain saw FIGBar and chain FIG Feed unit for chain sawmill with electric motor FIGMotors Chain saw engine FIGElectric Motor FIG Electric motor feed unit FIGHeight Adjustment B RailsLog Bolsters a Folding Stops CAdjustable Support Feet Rail StopRail Guard Safety Devices Installation InstallationInstallation Site UnpackingSetting up the Saw Carriage FIG Saw Carriage Adjustment FIGInstall chain saw and bar FIG Install the bar FIGOne-man sawmill with chain saw engine One-man sawmill with electric motorInstall scale pointer and scale FIG Install the handlebar FIGInstall throttle and cable FIG Adjusting the bar Checking the barFuel Handling Fuel chain saw enginePetrol Two-stroke oil MixingFuelling Starting and Stopping Starting a cold chain saw engine FIGStopping the chain saw engine FIG Starting the electric sawmill FIG Starting the electric sawmill with feed FIGUSE Securing the LogCalculating the Yield SawingStarting the Petrol Engine Starting the Electric MotorEdging FIG Maintenance Clutch drumSaw chain Saw unit’s height adjustment Drive beltMaintenance Daily maintenanceWeekly maintenance Monthly maintenanceTechnical Data Technical dataNoise Levels Vibration LevelsEU Declaration of Conformity only applies to Europe Page 114 02 2004W12
Top Page Image Contents