Husqvarna Complete Guide for Assembling Your Trimmer
Page 15

ASSEMBLY

arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

Fitting the blade guard and saw blade (235R)

•Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown.

K

J

H

I

A

L

CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

G

F

D

B

C

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support flange (F) on the output shaft.

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade

guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

•When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade.You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

Fitting a trimmer guard and Superauto II 1" trimmer head (232R)

K

G

F

K IB

C

J M

I L

A

•Fit the correct trimmer guard (A) for use with the trimmer head. Secure the trimmer guard using the 4 screws (L) and the support plate (M) as shown.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows:

•Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half

(K). Pull apart the trimmer head, grasping the cover firmly.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 232R 235R Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsMachine′s safety equipment Stop switchThrottle lock Muffler Cutting attachment guardVibration damping system Quick releaseLocking nut Cutting equipmentCutting equipment Sharpening grass cutters and grass bladesSharpening the saw blade Trimmer head Assembly Fitting the handlebar 232RFitting the handlebar 235R Transport position, handlebar Fitting blades and trimmer headsFitting a blade guard, grass blade and grass cutter 232R Fitting the blade guard and saw blade 232R Fitting a blade guard, grass blade and grass cutter 235RFitting the blade guard and saw blade 235R Fitting the trimmer guard and trimmer head Trimmy SII 235R Fitting other guards and cutting attachments 232RCorrect height Adjusting the harness and clearing sawFitting other guards and cutting attachments 235R Spreading the load on your shouldersFuel safety Fuel HandlingFuel Mixing FuelingCold engine Starting and StoppingCheck before starting Starting and stoppingWarm engine StartingStopping ABC of clearing Basic safety rulesWorking Techniques General working instructionsWorking methods Forestry clearing using a saw bladeGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head Clearing Carburetor MaintenanceCorrectly adjusted carburetor MufflerHigh speed jet H Air filter Cleaning the air filterCooling system Bevel gearSpark plug Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataTechnical Data Warranty Commencement Date Super Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R2¶5n¨ T45 1150185-95 ´z+R2¶5n¨ ´z+R2¶5n¨
Top Page Image Contents