Husqvarna 235R manual Fitting other guards and cutting attachments 232R

Page 16

ASSEMBLY

•Place the cover (I) and the support flange (F) on the output shaft.

•Fit the nut (G). Tighten the nut to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Grasp the handle of the spanner as close to the trimmer guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left- hand thread).

•Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

•Screw on the trimmer head (H) in the opposite direction to the direction of rotation.

H

•Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm).

•To dismantle, follow the instructions in the reverse order.

Fitting other guards and cutting attachments (232R)

•To dismantle, follow the instructions in the reverse order.

A

M

L B

C

Fitting the trimmer guard and trimmer head Trimmy SII (235R)

•Fit the correct trimmer guard (A) for use with the trimmer head. CAUTION! Ensure that the guard extension is fitted.

Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

H

L

M

C BA

AM L

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Secure the trimmer guard/combination guard using four screws (L) and the support plate (M) as shown.

•Fit the drive disc (B) on the output shaft.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

H

H

16 – English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 232R 235R KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentStop switch Machine′s safety equipmentThrottle lock Cutting attachment guard Vibration damping systemQuick release MufflerCutting equipment Locking nutSharpening grass cutters and grass blades Cutting equipmentSharpening the saw blade Trimmer head Fitting the handlebar 232R AssemblyFitting the handlebar 235R Fitting blades and trimmer heads Transport position, handlebarFitting a blade guard, grass blade and grass cutter 232R Fitting a blade guard, grass blade and grass cutter 235R Fitting the blade guard and saw blade 232RFitting the blade guard and saw blade 235R Fitting other guards and cutting attachments 232R Fitting the trimmer guard and trimmer head Trimmy SII 235RAdjusting the harness and clearing saw Fitting other guards and cutting attachments 235RSpreading the load on your shoulders Correct heightFuel Handling Fuel safetyFuel Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineStarting Warm engineStopping Basic safety rules Working TechniquesGeneral working instructions ABC of clearingForestry clearing using a saw blade Working methodsBrush cutting with a saw blade Grass clearing using a grass bladeGrass trimming with a trimmer head Clearing Maintenance CarburetorMuffler Correctly adjusted carburetorHigh speed jet H Cleaning the air filter Cooling systemBevel gear Air filterSpark plug Maintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical Data Warranty Commencement Date Super Auto Super Auto II Page T35 Trimmy Hit Trimmy Hit Pro Trimmy SII Page S35 ´z+R2¶5n¨ T45 1150185-95 ´z+R2¶5n¨ ´z+R2¶5n¨
Top Page Image Contents