Ryobi BC30 RY30564 manual Attaching the Front Handle CS30 and SS30, Attaching the J Handle BC30

Page 11

ASSEMBLY

ATTACHING THE FRONT HANDLE - CS30 AND SS30

See Figure 4.

Remove 2 wing nuts, 2 bolts, and clamp from the front handle.

Install the front handle onto the top side of the drive shaft housing and move it to a comfortable position.

Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

Reinstall the clamp, bolts, and wing nuts.

Tighten wing nut securely.

ATTACHING THE “J” HANDLE - BC30

See Figure 5.

A “J” handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter.

Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator’s left.

Insert the end of the handle between the clamps.

Align the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.) through the handle side.

Place short bolt (1/4-20 x 1 in.) through opposite side of clamp. Install flat washers, lock washers, and hex nuts to hold the assembly in place.

After assembly is complete, adjust the position of the handle for best balance and comfort.

Tighten first the long bolt and then the short bolt.

FRONT HANDLE

BOLT

 

 

WING

 

 

NUT

 

 

CLAMP

 

 

Fig. 4

 

BOLT

 

FRONT

1/4-20 x 1 in.

BOLT

 

 

1/4-20 x 1-1/2 in.

HANDLE

 

 

 

 

 

STRAP

 

 

HANGER

CLAMP

 

 

CLAMP

FLAT WASHER

 

LOCK WASHER

HEX NUT

Fig. 5

11

Image 11
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Specific Safety RulesSpecific Safety Rules for Trimmer USE Symbol Name Explanation SymbolsSymbol Signal Meaning ServiceString Head Coupler Throttle TriggerKnob FeaturesCoupler Assembly See Figure Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerFlat Washer Attaching the Front Handle CS30 and SS30Attaching the J Handle BC30 Front Handle Bolt Wing NUT ClampAttaching the Brushcutter Guard BC30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 To Attach the Straight Shaft Grass Deflector SS30Converting from String Trimmer to Brushcutter BC30 Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Removing the TRI-ARCBLADE and Brushcutter GuardGear Head Flanged Washer Slot Installing the TRI-ARCBLADE and Brushcutter GuardOperation Removing the Straight Shaft Grass Deflector and String HeadOperating the Trimmer Fueling and Refueling the TrimmerGrass Deflector Line Trimming CUT-OFF Blade To Advance the Cutting LineTo Advance the Cutting Line Manually Cutting TipsCutting Technique Blade Operating the BrushcutterBlade Thrust TRI-ARCBLADESee Figures 21 Starting and StoppingTo Stop the Engine If Assistance is Required Starting this ProductSee Figures 23 MaintenanceGeneral Maintenance Spool ReplacementSee Figures 25 String ReplacementCleaning the Exhaust Port and Muffler Spark ArrestorStoring the Product Cleaning the AIR Filter ScreenSpark Plug Replacement Fuel CAPFast TroubleshootingSpeed. See Figure This Product WAS Manufactured with a Catalyst Muffler WarrantyLimited Warranty Statement MANUFACTURER’S Warranty Coverage California Proposition Parts and Service