Ryobi CS30 RY30524 Attaching the Grass Deflector, To Attach the Curved Shaft Grass Deflector CS30

Page 12

ASSEMBLY

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS30

See Figure 6.

Remove hex screw, flat washer, lock washer, and wing nut from grass deflector.

Press the grass deflector onto the bottom of the curved shaft as shown.

Insert the hex screw through the grass deflector and the bracket on the curved shaft.

Place the flat washer and lock washer on the hex head cap screw.

Place the wing nut on the hex head cap screw and tighten securely.

TO ATTACH THE STRAIGHT SHAFT GRASS DEFLECTOR - SS30

See Figure 7.

Remove the wing screw from the grass deflector.

Insert the tab on the mounting bracket in the slot on the grass deflector.

Align the screw hole in the mounting bracket with the screw hole in the grass deflector.

Insert the wing screw through the mounting bracket and into the grass deflector.

Tighten the screw securely.

ATTACHING THE BRUSHCUTTER GUARD - BC30

See Figure 8.

The guard is shipped installed on these brushcutter models. Instructions have been included for reference when changing from string trimmer operation back to brushcutter operation.

With the string head removed, place the brushcutter guard on the gear head as shown.

Install the three hex head screws from bottom through the guard and into the gear head.

Tighten the screws securely and torque to 40-50 in.lb. minimum.

HEX

SCREWGRASS DEFLECTOR

BRACKET

 

LOCK

 

WASHER

FLAT

 

WASHER

WING NUT

 

Fig. 6

 

WING

 

SCREW

STRAIGHT

SHAFT GRASSTAB

DEFLECTOR

SLOT

Fig. 7

GEAR

BRUSHCUTTER GUARD

HEAD

 

HEX HEAD

SCREW

Fig. 8

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules Specific Safety Rules for Trimmer USESpecific Safety Rules for BRUSH- Cutter and Blade USE Symbols Symbol Name ExplanationService Symbol Signal MeaningCoupler Throttle Trigger String HeadFeatures CouplerKnob Assembly Installing the Power Head to the Attachment Removing the Attachment from the Power HeadAttaching the Storage Hanger See FigureAttaching the Front Handle CS30 and SS30 Attaching the J Handle BC30Front Handle Bolt Wing NUT Clamp Flat WasherAttaching the Grass Deflector To Attach the Curved Shaft Grass Deflector CS30To Attach the Straight Shaft Grass Deflector SS30 Attaching the Brushcutter Guard BC30Attaching the Shoulder Harness BC30 Converting from Brushcutter to String Trimmer BC30Removing the TRI-ARCBLADE and Brushcutter Guard Converting from String Trimmer to Brushcutter BC30Installing the TRI-ARCBLADE and Brushcutter Guard OperationRemoving the Straight Shaft Grass Deflector and String Head Gear Head Flanged Washer SlotFueling and Refueling the Trimmer Operating the TrimmerTo Advance the Cutting Line To Advance the Cutting Line ManuallyCutting Tips Grass Deflector Line Trimming CUT-OFF BladeOperating the Brushcutter Blade ThrustTRI-ARCBLADE Cutting Technique BladeStarting and Stopping To Stop the EngineIf Assistance is Required Starting this Product See Figures 21Maintenance General MaintenanceSpool Replacement See Figures 23String Replacement Cleaning the Exhaust Port and MufflerSpark Arrestor See Figures 25Cleaning the AIR Filter Screen Spark Plug ReplacementFuel CAP Storing the ProductTroubleshooting Speed. See FigureFast Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage Parts and Service California Proposition
Top Page Image Contents