Ryobi SS30 RY30240, CS30 RY30220 manual Troubleshooting, Speed. See Figure, Idle Speed Screw

Page 22

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

Engine will not start

1. No spark.

2. No fuel.

3. Engine is flooded.

1.Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug.

2.Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a service dealer. If primer bulb fills, engine may be flooded, proceed to next item.

3.Set the start lever to the START position. Squeeze the trigger and pull the rope repeatedly until the engine starts and runs.

NOTE: Depending on the severity of the flooding, this may require numerous pulls of the rope. See

Figure 23.

Engine does not reach full speed and emits excessive smoke

1.Incorrect oil/fuel mixture.

2.Air filter is dirty.

3.Spark arrestor screen is dirty.

4.Spark plug fouled.

1.Use fresh fuel and the correct 2-cycle oil mix. (50:1).

2.Clean air filter. Refer to Replacing and Cleaning Air Filter earlier in this manual.

3.Contact a servicing dealer.

4.Clean or replace spark plug. Reset spark plug gap. Refer to Spark Plug Replacement earlier in this manual.

Engine starts, runs, and ac-

1.

Idle speed screw on carburetor

1. Turn idle speed screw clockwise to increase idle

 

needs adjustment.

celerates but will not idle

 

 

speed. See Figure 31.

 

 

 

 

 

 

 

 

 

String will not advance

1. String is welded to itself.

1.

Lubricate string with silicone spray.

 

 

2.

Not enough string on spool.

2.

Install more string. Refer to String Replacement

 

 

 

 

 

earlier in this manual.

 

 

3.

String is worn too short.

3.

Pull strings while alternately pressing down on

 

 

 

 

 

and releasing spool retainer.

 

 

4.

String is tangled on spool.

4.

Remove string from spool and rewind. Refer to

 

 

 

 

 

String Replacement earlier in this manual.

 

 

5.

Engine speed is too slow.

5.

Advance string at full throttle.

 

 

 

 

 

 

 

IDLE SPEED

SCREW

Fig. 31

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbols Symbol Name ExplanationService Features Trigger Lock Primer Starter GripRope FrontAssembly Attaching the Storage Hanger Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head See FigureFront Handle Bolt Wing NUT Clamp Attaching the Front Handle CS30 and SS30Attaching the J Handle BC30 Flat WasherTo Attach the Straight Shaft Grass Deflector SS30 Attaching the Grass DeflectorTo Attach the Curved Shaft Grass Deflector CS30 Attaching the Brushcutter Guard BC30Removing the TRI-ARCBLADE and Brushcutter Guard Attaching the Shoulder Harness BC30Converting from Brushcutter to String Trimmer BC30 Converting from String Trimmer to Brushcutter BC30Operation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer Operating the TrimmerCutting Tips To Advance the Cutting LineTo Advance the Cutting Line Manually Grass Deflector Line Trimming CUT-OFF BladeTRI-ARCBLADE Operating the BrushcutterBlade Thrust Cutting Technique BladeTo Start a Cold Engine Starting and StoppingSee Figures 21 To Stop the EngineSpool Replacement MaintenanceGeneral Maintenance See Figures 24Arrows on Spool Anchor Hole String ReplacementSee Figures 26 First String SlotSpark Plug Replacement Cleaning the Exhaust Port and Muffler Spark ArrestorReplacing and Cleaning AIR Filter Fuel CAPSpeed. See Figure TroubleshootingIdle Speed Screw Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement Maintenance Requirements MANUFACTURER’S Warranty CoverageOWNER’S Warranty Responsibilities CoverageService

BC30 RY30260, SS30 RY30240, CS30 RY30220 specifications

The Ryobi SS30, RY30240, CS30 RY30220, and BC30 RY30260 are a series of versatile outdoor power equipment, each designed to tackle various landscaping and gardening tasks. Renowned for their reliability, these tools combine innovative technology with user-friendly features to enhance the gardening experience.

The Ryobi SS30, a versatile string trimmer, is equipped with a powerful 30cc 2-cycle engine that offers robust performance for trimming grass, weeds, and overgrowth. Its lightweight design ensures ease of maneuverability, while the adjustable dual-line head allows for quick line replacement and increased cutting efficiency. One innovative feature is the Auto Feed Spool, which automatically feeds the cutting line as needed, reducing downtime and enhancing productivity. The SS30 also boasts a 17-inch cutting width, making it ideal for small to medium-sized yards.

The RY30240 is a robust and efficient hedge trimmer designed for precision and versatility. This model incorporates a 40V lithium-ion battery, offering extended run time without the hassle of cords or gas. The dual-action blades help minimize vibrations and ensure clean cuts on branches up to ¾ inch thick. Its ergonomic design includes a rotating handle that allows for comfortable cutting in various angles, making it suitable for both horizontal and vertical trimming tasks. The RY30240 also features a lightweight body, ensuring that users can work for extended periods without fatigue.

The CS30 RY30220 is a chain saw designed for performance and safety. It features a durable 30cc 2-cycle engine combined with a low kickback 12-inch bar, making it perfect for tackling light cutting tasks, such as pruning and light firewood cutting. Safety features, including a chain brake and handguard, prioritize user protection while offering powerful cuts. Additionally, the easy-access chain tensioning system allows for quick adjustments without the need for tools, ensuring continuous work without interruptions.

Lastly, the BC30 RY30260 is a powerful brush cutter that features a robust 30cc 2-cycle engine. Its long feed line allows for effective clearing of stubborn brush and thick grass. The BC30 offers a unique brush cutter blade option for heavier vegetation, providing users with the flexibility to switch between tools depending on the task at hand. The ergonomic design ensures comfort, reducing strain during long hours of tackling tough landscaping jobs.

In conclusion, the Ryobi SS30, RY30240, CS30 RY30220, and BC30 RY30260 each serve as reliable solutions for homeowners and landscaping professionals. Their combination of power, innovative technology, and ergonomic design makes them indispensable tools for maintaining beautiful outdoor spaces.
Top Page Image Contents