Ryobi SS30 RY30240, CS30 RY30220, BC30 RY30260 manual Specific Safety Rules for Trimmer USE

Page 4

SPECIFIC SAFETY RULES

SPECIFIC SAFETY RULES FOR TRIMMER USE

Replace string head if cracked, chipped, or damaged in any way. Be sure the string head or blade is properly installed and securely fastened. Failure to do so can cause serious injury.

Make sure all guards, straps, deflectors, and handles are properly and securely attached.

Use only the manufacturer’s replacement string in the cutting head. Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury.

Never operate unit without the grass deflector in place and in good condition.

Maintain a firm grip on both handles while trimming. Keep string head below waist level. Never cut with the string head located over 30 in. (76 cm) or more above the ground.

SPECIFIC SAFETY RULES FOR BRUSH- CUTTER AND BLADE USE

After engine stops, keep rotating blade in thicker weeds or pulpy stalks until it stops.

Do not operate the brushcutter unless the brushcutter guard is firmly secured in place and in good condition.

Use heavy gloves when operating the brushcutter and when installing or removing blades.

Always stop the engine and remove the spark plug wire before attempting to remove any obstruction caught or jammed in the blade or before removing and installing the blade.

Do not attempt to touch or stop the blade when it is rotating.

A coasting blade can cause injury while it continues to spin after the engine is stopped or throttle trigger released. Maintain proper control until the blade has completely stopped rotating.

Replace any blade that has been damaged. Always make sure blade is installed correctly and securely fastened before each use. Failure to do so can cause serious injury.

Use only the manufacturer’s replacement Tri-Arc®blade intended for use on this brushcutter. Do not use any other blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury.

The Tri-Arc®blade is suited for cutting thicker weeds or pulpy stalks only. Do not use for any other purpose. Never use the Tri-Arc®blade to cut woody brush.

Exercise extreme caution when using the blade with this unit. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut. This contact may cause the blade to stop for an instant, and suddenly “thrust” the unit away from the object that was hit. This reaction can be violent enough to cause the op- erator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut from the right to the left. In the event an unexpected object or woody stock is encountered, this could minimize the blade thrust reaction.

Never cut any material over 1/2 in. (13 mm) diameter.

Always wear the shoulder harness when using the brush- cutter and adjust to a comfortable operating position. Maintain a firm grip on both handles while cutting with a blade. Keep the blade away from your body and below waist level.

Never use the brushcutter with the blade located 30 in. (76 cm) or more above the ground level.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules for Trimmer USE Specific Safety RulesSpecific Safety Rules for BRUSH- Cutter and Blade USE Symbols Symbol Name ExplanationService Features Starter Grip RopeTrigger Lock Primer FrontAssembly Installing the Power Head to the Attachment Removing the Attachment from the Power HeadAttaching the Storage Hanger See FigureAttaching the Front Handle CS30 and SS30 Attaching the J Handle BC30Front Handle Bolt Wing NUT Clamp Flat WasherAttaching the Grass Deflector To Attach the Curved Shaft Grass Deflector CS30To Attach the Straight Shaft Grass Deflector SS30 Attaching the Brushcutter Guard BC30Attaching the Shoulder Harness BC30 Converting from Brushcutter to String Trimmer BC30Removing the TRI-ARCBLADE and Brushcutter Guard Converting from String Trimmer to Brushcutter BC30Operation Installing the TRI-ARCBLADE and Brushcutter GuardRemoving the Straight Shaft Grass Deflector and String Head Fueling and Refueling the Trimmer Operating the TrimmerTo Advance the Cutting Line To Advance the Cutting Line ManuallyCutting Tips Grass Deflector Line Trimming CUT-OFF BladeOperating the Brushcutter Blade ThrustTRI-ARCBLADE Cutting Technique BladeStarting and Stopping See Figures 21To Start a Cold Engine To Stop the EngineMaintenance General MaintenanceSpool Replacement See Figures 24String Replacement See Figures 26Arrows on Spool Anchor Hole First String SlotCleaning the Exhaust Port and Muffler Spark Arrestor Replacing and Cleaning AIR FilterSpark Plug Replacement Fuel CAPSpeed. See Figure TroubleshootingIdle Speed Screw Warranty This Product WAS Manufactured with a Catalyst MufflerLimited Warranty Statement MANUFACTURER’S Warranty Coverage OWNER’S Warranty ResponsibilitiesMaintenance Requirements CoverageService

BC30 RY30260, SS30 RY30240, CS30 RY30220 specifications

The Ryobi SS30, RY30240, CS30 RY30220, and BC30 RY30260 are a series of versatile outdoor power equipment, each designed to tackle various landscaping and gardening tasks. Renowned for their reliability, these tools combine innovative technology with user-friendly features to enhance the gardening experience.

The Ryobi SS30, a versatile string trimmer, is equipped with a powerful 30cc 2-cycle engine that offers robust performance for trimming grass, weeds, and overgrowth. Its lightweight design ensures ease of maneuverability, while the adjustable dual-line head allows for quick line replacement and increased cutting efficiency. One innovative feature is the Auto Feed Spool, which automatically feeds the cutting line as needed, reducing downtime and enhancing productivity. The SS30 also boasts a 17-inch cutting width, making it ideal for small to medium-sized yards.

The RY30240 is a robust and efficient hedge trimmer designed for precision and versatility. This model incorporates a 40V lithium-ion battery, offering extended run time without the hassle of cords or gas. The dual-action blades help minimize vibrations and ensure clean cuts on branches up to ¾ inch thick. Its ergonomic design includes a rotating handle that allows for comfortable cutting in various angles, making it suitable for both horizontal and vertical trimming tasks. The RY30240 also features a lightweight body, ensuring that users can work for extended periods without fatigue.

The CS30 RY30220 is a chain saw designed for performance and safety. It features a durable 30cc 2-cycle engine combined with a low kickback 12-inch bar, making it perfect for tackling light cutting tasks, such as pruning and light firewood cutting. Safety features, including a chain brake and handguard, prioritize user protection while offering powerful cuts. Additionally, the easy-access chain tensioning system allows for quick adjustments without the need for tools, ensuring continuous work without interruptions.

Lastly, the BC30 RY30260 is a powerful brush cutter that features a robust 30cc 2-cycle engine. Its long feed line allows for effective clearing of stubborn brush and thick grass. The BC30 offers a unique brush cutter blade option for heavier vegetation, providing users with the flexibility to switch between tools depending on the task at hand. The ergonomic design ensures comfort, reducing strain during long hours of tackling tough landscaping jobs.

In conclusion, the Ryobi SS30, RY30240, CS30 RY30220, and BC30 RY30260 each serve as reliable solutions for homeowners and landscaping professionals. Their combination of power, innovative technology, and ergonomic design makes them indispensable tools for maintaining beautiful outdoor spaces.
Top Page Image Contents