Ryobi 990r manual California Emission Regulations, Safety Warnings, Fuel and PRE-OPERATIONAL

Page 3

CALIFORNIA EMISSION REGULATIONS

The engine of your lawn and garden care product meets the 1995 California emissions regulations. To ensure that your unit continues to meet these regulations, refer to the following information and instructions in this operator's manual.

These units are identified by the label on the engine of your product. A typical identification label is shown.

SAFETY WARNINGS

THE PURPOSE OF SAFETY SYMBOLS IS TO ATTRACT YOUR ATTENTION TO POSSIBLE DANGERS. THE SAFETY SYMBOLS, AND THE EXPLANATIONS WITH THEM, DESERVE YOUR CAREFUL ATTENTION AND UNDERSTANDING. THE SAFETY WARNINGS DO NOT BY THEMSELVES ELIMINATE ANY DANGER. THE INSTRUCTIONS OR WARNINGS THEY GIVE ARE NOT SUBSTITUTES FOR PROPER ACCIDENT PREVENTION MEASURES.

SYMBOL

MEANING

 

 

WARNING:

Failure to obey a safety

warning can result in injury to yourself and others.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

FUEL AND PRE-OPERATIONAL

•Fuel is extremely flammable and its vapors can explode if ignited. Always stop the engine and allow it to cool before filling the fuel tank. Do not smoke while filling the fuel tank. Keep sparks and open flames away from the area.

•Store fuel only in containers designed and approved for the storage of such materials.

•Pressure can build up in the fuel tank. Loosen the fuel tank cap slowly to relieve any pressure in the tank.

•Add fuel in a clean, well-ventilated area. Wipe up any spilled fuel immediately. If fuel has been spilled, allow it to dry completely before starting the engine.

•Move the trimmer at least 3 m (10 ft) from the fueling point before starting the engine.

•Thoroughly inspect the trimmer for loose or damaged parts before each use. Do not use until adjustments or repairs are made.

•Avoid accidental starting. Be in the starting position whenever pulling the starting rope.

•Keep all bystanders, especially children, and pets at least 10 m (33 ft) away from the area.

•Carefully inspect the areas to be cut. Remove all debris that could become entangled in the string or blade. Also remove any objects that could be thrown during cutting.

•Before starting, make sure the string head is not in contact with anything.

•Check the oil level before each use.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 990r Introduction Table of Contents Safety Warnings California Emission RegulationsFuel and PRE-OPERATIONAL After USE Other Safety WarningsOperational Saftey Warnings for Brush Blade During USESymbol Safety and International SymbolsBrushcutter Safety Assembly Instructions Adjusting the J-HANDLEInstalling the Shoulder Strap Installing the Brush Blade Installing the Line Spool Blade LocatingMark Installing the Lower Attachment Boom Operating Split Boom CouplerRemoving the Lower Attachment Boom Checking the OIL OIL & Fuel InformationRecommended OIL Type Adding OIL to Crankcase Initial USEUSE of Blended Fuels Changing the OILRecommended Fuel Type Definition of Blended FuelsRope STARTING/STOPPING InstructionsThrottle Trigger PositionDecorative Trimming Adjusting the Trimming Line LengthUsing the Brush Blade Operating InstructionsFrequency Maintenance Required Refer to Maintenance and Repair Instructions Maintenance ScheduleBump Knob Inner Reel Rewinding the Existing ReelCorrect Line to Use Removing the Existing ReelReinstalling the Reel Installing a Prewound ReelWinding the Existing Reel Fill Plug Gear Housing ServiceScrews Choke Lever AIR Filter MaintenanceScrew Air FilterFinal High Speed Mixture Needle Adjustment Carburetor AdjustmentAdjusting the Carburetor Air Filter MaintenanceINSPECTING/CLEANING the Muffler Lean Adjust to Midpoint RichRemoving Muffler Torque the screw to 15-20 inlb 1.7-2.2 Nm Inspection and CleaningMuffler Reassembly Checking Spark Arrester ScreenChecking / Adjusting Valve to Rocker ARM Clearance Replacing the Spark PlugScrew Screws Rocker Arm Valve Flat Feeler Gauge Adjusting NutsEngine Cleaning and StorageSpecifications Cold Torque SpecificationsProblem Cause Action TroubleshootingYour Warranty Rights and Obligations California Emission Control Warranty StatementLimited Two-Year Warranty

990r specifications

The Ryobi 990R is a powerful and versatile cordless tool that has gained popularity among both DIY enthusiasts and professional users alike. Designed to offer convenience and efficiency, this innovative unit is equipped with a range of features that cater to different applications.

One of the standout characteristics of the Ryobi 990R is its powerful motor. With a robust design, it delivers ample torque and speed, enabling users to tackle a variety of tasks, from cutting through tough materials to drilling precise holes. The motor is powered by a high-capacity lithium-ion battery, which is known for its longevity and quick recharge time. This ensures that users can work longer without frequent interruptions, making the 990R an ideal choice for demanding projects.

Another notable feature of the Ryobi 990R is its ergonomic design. Lightweight and easy to maneuver, the unit minimizes user fatigue, especially during extended use. The integrated rubber grip offers enhanced comfort and control, allowing for greater precision when working on intricate tasks. This commitment to user comfort makes it suitable for both novice and experienced users.

The 990R also incorporates advanced technology that enhances its performance. The unit features variable speed settings, allowing users to adjust the tool’s speed according to the task at hand, whether it’s a delicate job or a high-powered application. Additionally, the tool is equipped with a built-in LED light that illuminates the work area, ensuring visibility in dimly lit spaces and improving overall accuracy.

For added versatility, the Ryobi 990R is compatible with a wide range of attachments and accessories. This allows users to customize the tool according to their specific needs, whether they require a drill, sander, or impact driver. The quick-change chuck system further enhances efficiency, enabling users to switch between accessories in seconds.

Durability is another defining characteristic of the Ryobi 990R. Constructed with high-grade materials, it is designed to withstand demanding working conditions without compromising performance. This resilience is crucial for professionals who rely on their tools for everyday use.

In summary, the Ryobi 990R stands out in the crowded tool market due to its powerful motor, ergonomic design, advanced technologies, and durability. Whether for home improvement projects or professional applications, it offers reliability and performance that users can trust. As Ryobi continues to innovate, the 990R remains a solid choice for anyone looking to enhance their toolkit.
Top Page Image Contents