Ryobi 990r California Emission Control Warranty Statement, Your Warranty Rights and Obligations

Page 27

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Ryobi Outdoor Products (ROP), are pleased to explain the emission control system warranty on your 1995 and later lawn and garden equipment engine. In California, new lawn and garden equipment engines must be designed, built and equipped to meet the State's stringent anti-smog standards. ROP must warrant the emission control system on your lawn and garden equipment engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your lawn and garden equipment engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and catalytic converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, ROP will repair your lawn and garden equipment engine at no cost to you including diagnosis, parts and labor.

The 1995 and later utility and lawn and garden equipment engines are warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by ROP.

OWNER'S WARRANTY RESPONSIBILITIES:

•As the lawn and garden equipment engine owner, you are responsible for the perform- ance of the required maintenance listed in your operator's manual. ROP recommends that you retain all receipts covering maintenance on your lawn and garden equipment engine, but ROP cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

•As the lawn and garden equipment engine owner, you should however be aware that ROP may deny you warranty coverage if your lawn and garden equipment engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

•You are responsible for presenting your lawn and garden equipment engine to an Ryobi Authorized Service Center as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-345-8746.

MANUFACTURER'S WARRANTY COVERAGE:

•The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

•The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and workmanship which cause the failure of a warranted part for a period of two years.

•Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Ryobi Service Center. For the nearest location, please contact Ryobi at:

1-800-345-8746.

•Any warranted part which is not scheduled for replacement, as required maintenance which is scheduled only for regular inspection to the effect of "Repair or replace as nec- essary" is warranted for the warranty period. Any warranted part which is scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement point for that part.

•The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an Authorized Ryobi Service Center.

•The manufacturer is liable for damages to other engine components caused by the fail- ure of a warranted part still under warranty.

•Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

•The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures or warranted parts caused by the use of add-on or modified parts.

•In order to file a claim, go to your nearest Authorized Ryobi Service Center. Warranty services or repairs will be provided at all Authorized Ryobi Service Centers.

•Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durabili- ty may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer.

•The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel pick up/fuel filter, ignition module, spark plug and muffler.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 990r Introduction Table of Contents Safety Warnings California Emission RegulationsFuel and PRE-OPERATIONAL After USE Other Safety WarningsOperational Saftey Warnings for Brush Blade During USESymbol Safety and International SymbolsBrushcutter Safety Assembly Instructions Adjusting the J-HANDLEInstalling the Shoulder Strap Installing the Brush Blade Installing the Line Spool Blade LocatingMark Installing the Lower Attachment Boom Operating Split Boom CouplerRemoving the Lower Attachment Boom Checking the OIL OIL & Fuel InformationRecommended OIL Type Adding OIL to Crankcase Initial USEUSE of Blended Fuels Changing the OILRecommended Fuel Type Definition of Blended FuelsRope STARTING/STOPPING InstructionsThrottle Trigger PositionDecorative Trimming Adjusting the Trimming Line LengthUsing the Brush Blade Operating InstructionsFrequency Maintenance Required Refer to Maintenance and Repair Instructions Maintenance ScheduleBump Knob Inner Reel Rewinding the Existing ReelCorrect Line to Use Removing the Existing ReelReinstalling the Reel Installing a Prewound ReelWinding the Existing Reel Fill Plug Gear Housing ServiceScrews Choke Lever AIR Filter MaintenanceScrew Air FilterFinal High Speed Mixture Needle Adjustment Carburetor AdjustmentAdjusting the Carburetor Air Filter MaintenanceINSPECTING/CLEANING the Muffler Lean Adjust to Midpoint RichRemoving Muffler Torque the screw to 15-20 inlb 1.7-2.2 Nm Inspection and CleaningMuffler Reassembly Checking Spark Arrester ScreenChecking / Adjusting Valve to Rocker ARM Clearance Replacing the Spark PlugScrew Screws Rocker Arm Valve Flat Feeler Gauge Adjusting NutsEngine Cleaning and StorageSpecifications Cold Torque SpecificationsProblem Cause Action TroubleshootingYour Warranty Rights and Obligations California Emission Control Warranty StatementLimited Two-Year Warranty

990r specifications

The Ryobi 990R is a powerful and versatile cordless tool that has gained popularity among both DIY enthusiasts and professional users alike. Designed to offer convenience and efficiency, this innovative unit is equipped with a range of features that cater to different applications.

One of the standout characteristics of the Ryobi 990R is its powerful motor. With a robust design, it delivers ample torque and speed, enabling users to tackle a variety of tasks, from cutting through tough materials to drilling precise holes. The motor is powered by a high-capacity lithium-ion battery, which is known for its longevity and quick recharge time. This ensures that users can work longer without frequent interruptions, making the 990R an ideal choice for demanding projects.

Another notable feature of the Ryobi 990R is its ergonomic design. Lightweight and easy to maneuver, the unit minimizes user fatigue, especially during extended use. The integrated rubber grip offers enhanced comfort and control, allowing for greater precision when working on intricate tasks. This commitment to user comfort makes it suitable for both novice and experienced users.

The 990R also incorporates advanced technology that enhances its performance. The unit features variable speed settings, allowing users to adjust the tool’s speed according to the task at hand, whether it’s a delicate job or a high-powered application. Additionally, the tool is equipped with a built-in LED light that illuminates the work area, ensuring visibility in dimly lit spaces and improving overall accuracy.

For added versatility, the Ryobi 990R is compatible with a wide range of attachments and accessories. This allows users to customize the tool according to their specific needs, whether they require a drill, sander, or impact driver. The quick-change chuck system further enhances efficiency, enabling users to switch between accessories in seconds.

Durability is another defining characteristic of the Ryobi 990R. Constructed with high-grade materials, it is designed to withstand demanding working conditions without compromising performance. This resilience is crucial for professionals who rely on their tools for everyday use.

In summary, the Ryobi 990R stands out in the crowded tool market due to its powerful motor, ergonomic design, advanced technologies, and durability. Whether for home improvement projects or professional applications, it offers reliability and performance that users can trust. As Ryobi continues to innovate, the 990R remains a solid choice for anyone looking to enhance their toolkit.
Top Page Image Contents