Craftsman 358.796131- 26.2CC operating instructions Starter Rope Repair

Page 15

D. STARTER ROPE REPAIR

•Repair the starter rope If the rope breaks next to the pulley.

•Replace the starter rope if the rope breaks 2-3 inches away from the pulley as the rope will be too short to repair properly.

/_WARNING

Always wear eye protection when ser- vicing the starter rope. The recoil spring, located beneath the pulley, is under ten- sion. If the spring pops out, serious per- sonal injury can result.

•To repair or replace:

NOT_ Use caution when separating the fan housing from the shroud to avoid breaking or damaging the fuel line fittings.

1_ Drain all fuel from tank.

17.Hold the 12 inch slack in the rope and catch rope in pulley notch. Figure 30.

18.Hold the rope taut and make 2 complete turns of the pulley counterclockwise

to place tension on the pulley. Hold the pulley to retain tension.

19.Align pulley notc_ with rope exit hole,

pull starter handl_tothe full extent of the rope and allow the rope to slowly wind around the pulley.

NOTE: While the unit is disassembled, in- spect the carburetor housing seal and replace if worn. Figure 28.

20.Reverse procedure for re-assembly of fan housing to shroud.

NOTE: Make sure the fuel line with the black stripe or solid color is installed on

2.Remove the four (4) screws from fan housing. Figure 28.

3.Carefully separate fan housing from shroud- about one (1) inch.

4.Disconnect fuel lines from fittings.

5.Disconnect ignition module wires. Figure 28.

6.Slide high tension lead grommet from slot, in fan housing.

7.Separate the fan housing completely from the shroud.

GROMMET

SHROU[

i.i

i

i

I IGNITION MODULE WIRES

8.If the starter rope is not broken, release the spring tension by pulling about 12 inches of rope from the pulley and catch the rope in the notch as shown. Figure 30.

NOTE: The tension on thestarter spring will be released if the rope has broken.

9.Remove screw and pulley very carefully. Figure 29. The recoil spring which lies beneath the pulley must stay in the hous- Ing, flat against t6e bottom. Itthe spring Is disturbed, it will require oonsiderable time and effort to reinstall. Twist the pulley

gently clockwise ,,,,-]&'as you pull up to release the spring.

10.Moveawayfromthefuel tankand melttheend0f the new rope to go intothe pulley,

11.Allowthe melted endtoddponce, then while rope isstillhot pullthe melted end through a clean rag to obtain a smooth, pointed end.

12.Insert rope through the rope exit hole in the fan housing.

13.Guide rope insidepulley,then upthrough topside pulley hole by pushing the rope from the under-

side hole with a small object such as a screwdriver.

14.Wrap rope counterclockwise 4[--,,around pulley ratchet and tuck loose end back

under-rope leaving a 1/4 to I/2 inch tail laying in the rope groove. Figure 30.

15.Wind all but about 12 inches of the rope

counterclockwise _ around pulley.

16.Replace pulley in the housing. Be sure the pulley is all the way down and the spring is secured. Replace screw and tighten. Figure 29.

CARBURETOR

FAN

HOUSING

3USING

FUEL LINE FITTINGS

LINES

iii

Figure 28

,o., ,o.,

NOTCH

Figure 29

Figure 30

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents RnFT,SMn Specifications Table of ContentsOperate Your Unit Safely Aiknow Your UnitPlan Ahead Handle Fuel with CautionKnow Your Weedwacker Trimmer IntroductionUnpacking Instructions Read Your Operators Manual AssemblyAssemblysteps PreparationAutomotive OIL EngineinformationFuelingyour Unit Fuel MixtureStarting Instructions HOW Fuel Injection Starting TM Works PRE-OPERATION ChecksAfter starting and engine runs smoothly Starting ProcedureBelow 30F Temperature Pull starter rope quickly and sharply until engine startsCarburetor Adjustments =OPERATING InstructionsSpark Plug Inspect the area to be cut Using Your UnitOperating Instructions Advancing the Cutting LineTrimming Cutting MethodsAlways cut left to right RightwrongClean dirt and debris from housing Cutting Head Maintenance Cutting Line ReplacementSpool Replacement Line Limiter MaintenanceTAP Button Normal Spool Worn Spool Wipethe Flexible Drive Shaft LubricationAIR Filter Care Fuel Tank UpkeepStarter Rope Repair Trouble CauseRemedy Accessories Accessories101 2628 STD KEY Part QTY Description Pari Recl REQSears Weedwacker Parts List -- Model 358.796131-26.2cc 511010 15274 Decals 26568 KEY Part QTY NO. NO. REQKEY Part QTY REQ 15123 15479 26O32 10738 16563Sears Weedwacker Parts List -- Model 358.796131-26.2cc 32 19105 33 21055 34 19131 35 26047 4205954I 15127 39114 Spring Starter DogQTY KEY Part REQ Description KEY Part NO. noPage Page Starting the Engine MaintenanceQuick Reference Fueling358.796131 Sears Service Is AT Your Service

358.796131- 26.2CC specifications

The Craftsman 358.796131 is a robust and reliable 26.2CC gas-powered string trimmer designed for both homeowners and professionals who require efficient gardening tools. Equipped with a powerful 26.2cc 2-cycle engine, this string trimmer delivers dependable performance for a variety of lawn care tasks, including trimming, edging, and clearing overgrown areas.

One of the standout features of the Craftsman 358.796131 is its lightweight and ergonomic design. Weighing in at only 11.5 pounds, this trimmer is comfortable to handle, allowing users to operate it for extended periods without fatigue. The well-balanced construction ensures optimal maneuverability, making it easy to navigate around flower beds, trees, and other obstacles in your yard.

In terms of technology, the Craftsman 358.796131 incorporates the Easy Start system, which significantly reduces the effort required to start the engine. This feature minimizes the pull required on the starter cord, allowing for quick and hassle-free starts every time. This is particularly beneficial for users who may struggle with traditional starting methods, as it enhances the overall user experience.

The trimmer is also equipped with a 17-inch cutting swath, allowing users to cover more ground in less time. The dual-line bump feed head provides a continuous flow of line, ensuring that the cutting area is maximized with minimal interruptions. The ability to easily advance the line by simply bumping the head against the ground allows for convenient operation while working in various terrains.

Another noteworthy characteristic of the Craftsman 358.796131 is its durability. The trimmer is constructed with high-quality materials and components designed to withstand the rigors of regular use in tough outdoor conditions. The solid build ensures longevity, making it a worthwhile investment for anyone looking to keep their outdoor spaces well-maintained.

Moreover, the Craftsman trimmer includes a variety of attachments and accessories, enhancing its versatility. These accessories can help tackle different tasks, from edging to clearing taller weeds and brush.

In conclusion, the Craftsman 358.796131 is a powerful, user-friendly, and versatile solution for lawn care enthusiasts. Its combination of performance, technology, and durability makes it an excellent choice for both residential and professional lawn maintenance, ensuring that users can achieve a well-groomed yard with ease and efficiency.
Top Page Image Contents