Craftsman 358-79104 Howto Stop Your Unit, Cutting Methods, Mowing, Trimming, Sweeping

Page 13

Alwaysreleasethethrottletriggerand allowtheenginetoreturntoidle speedwhennotcutting.

HOWTO STOP YOUR UNIT

•Release the throttle trigger.

•Move the ON/OFF switch to the OFF

position.

CUTTING METHODS

,i_WARNING: Use minimum

speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

•The tip of the line does the cutting. You will achieve the best perform- ance and minimum line wear by not crowding the line into the cutting

area. The right and wrong ways are shown below.

Tip of the Line

Line Crowded Into

Does The Cutting

Work Area

RightWrong

SCALPING - The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trim- mer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

Scalping

3 inches (8 cm)

 

above ground

MOWING - Your trimmer is ideal for

mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

•The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

•For trimming or scalping, use less than full throttle to increase line life

and decrease head wear, especially:

•During light duty cutting.

•Near objects around which the line

can wrap such as small posts, trees or fence wire.

TRIMMING - Hold the bottom of the

trimmer head about 3 inches (8 cm) above the ground and at an angle. Al- low only the tip of the line to make

contact with vegetation. Do not force trimmer line into work area.

Trimming

3 inches (8 cm)

above ground

SWEEPING - The fanning action of the rotating line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.

Sweeping

/

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 545140962 12/15/06 Operators ManualSears, Roebuck and Co., Hoffman Estates, IL Oneyear Full Warranty on Craftsman GAS WeedwackerOperator Safety This power unit can be dangerous! Op4WARNING Fuel Safety Unit / Maintenance SafetyTransporting and Storage Edger Safety Line Trimmer SafetyBlowernacuum Safety Blade rotatesCultivator Safety Brushcutter SafetyPole Pruner Safety Hedge Trimmer SafetyCarton Contents Snow Thrower SafetyAssembly MentAttaching Shield Adjusting the HandlePrimer Bulb Knowyour TrimmerStart Lever Before Starting EngineStarting Warm Engine Convertible TM FeatureYour Unit Starting Flooded EngineMents Installing Optional AttachOperating Instructions Operating Position Always USECutting Methods Howto Stop Your UnitMowing TrimmingMaintenance Maintenance ScheduleAIR Filter Inspect Muffler and Spark Arresting ScreenCarburetor Adjustment Line ReplacementReplace Spark Plug Seasonal Storage Idle Speed AdjustmentFuel System OtherCause Remedy TroubleshootingWarranty Commencement Your Warranty Rights and OBEmission Control Warranty MAINTENANCE, Replacement and Repair of Emission RE41 I 61 I 81

358-79104 specifications

The Craftsman 358-79104 is a robust and reliable string trimmer designed to make yard maintenance more efficient and enjoyable. This versatile tool is ideal for both homeowners and landscaping professionals who require a powerful solution for cutting grass, weeds, and underbrush in various terrains.

One of the standout features of the Craftsman 358-79104 is its 25cc, 2-cycle engine. This powerful engine provides ample power to tackle tough trimming tasks with ease. The 2-cycle design ensures high performance while remaining lightweight, making it easy to maneuver around your yard without straining. The engine is also designed for easy starting, reducing the frustration often associated with starting gas-powered equipment.

Another significant feature of the Craftsman 358-79104 is its flexible cutting head design. This trimmer comes with a dual line bump head that allows for a wider cutting swath. The ability to easily feed line by simply bumping the head on the ground is a convenient touch that eliminates the need to stop and rethread the line frequently. This feature not only enhances productivity but also allows for cleaner cuts, promoting healthier grass growth.

The ergonomic design of the Craftsman 358-79104 is built for user comfort. It features an adjustable handle that can be customized to fit the operator's height, reducing fatigue during extended use. The soft-grip handle also provides added comfort and better control, ensuring a precise and comfortable cutting experience.

Another innovative characteristic of this trimmer is its versatile design; it can be easily converted into other tools, such as a brush cutter or edger, by simply attaching compatible accessories. This multi-functional capability greatly enhances the value of the Craftsman 358-79104, making it a worthy investment for anyone looking to maintain their landscape.

In summary, the Craftsman 358-79104 string trimmer delivers a powerful, efficient, and versatile solution for yard maintenance. With its strong 25cc 2-cycle engine, flexible cutting options, ergonomic design, and multi-functionality, this trimmer is a reliable choice for achieving a well-groomed lawn. Whether you're performing routine trimming or tackling overgrown areas, the Craftsman 358-79104 is engineered to handle the job with ease and precision.
Top Page Image Contents