Snapper R204513E important safety instructions Stopping, Handle Height Adjustment

Page 11

Section 2 - OPERATING INSTRUCTIONS

2.2STARTING & OPERATION 2.2.2. ENGINE & BLADE (120 Volt Electric Start)

4.Stand in operator’s position. Move blade control against handle and hold in place. See Figure 2.5.

WARNING

To avoid electrical shock or injury, make sure power cord is away from cutting blade before attempting to start engine.

5.Depress starter button on switch box until engine starts. See Figure 2.5. NOTE: If after 5 seconds of cranking the engine and it does not start, release the starter button. Attempt starting again after waiting for approximately 20 seconds.

6.After engine starts, allow a brief warm-up until engine runs smooth. If engine fails to start, check the power cord. Be sure it is inserted securely into the AC receptacle and into the switch box.

2.3STOPPING

Stop engine and blade by releasing the blade control. See Figure 2.6.

WARNING

Before attempting any adjustments to the cutting height, STOP the engine, remove the spark plug wire from the spark plug and secure wire away from plug. DO NOT make any adjustments with engine or blade running. Be extremely careful when performing adjustments around engine. Engine is extremely hot and can cause severe burns. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

2.4HANDLE HEIGHT ADJUSTMENT

The height of the mower handle can be adjusted as follows:

1.Loosen the lower nuts on each lower handle as shown in Figure 2.7.

2.Move upper mower handle up or down until the desired position is achieved.

3.Tighten the lower nuts on each lower handle to maintain desired position.

LOWER HANDLE

LOOSEN TWO

NUTS

BLADE CONTROL

SHOWN IN “OFF”

POSITION

FIGURE 2.6

FIGURE 2.7

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Steel Deck Walk Mowers Series Operation Protection for ChildrenSlope Operation PreparationMaintenance and Storage Table of Contents Steel Deck Walk Behind Mowers CONSUMER/OPERATOR Product Registration Card LubricationOperational Test DEALER’S Records & Final CheckPage Nomenclature IntroductionStarting & Operation 2.2.1. Engine & Blade PRE-START Check ListOptional Power Cords Minimum Gauge for Cord Sets Stopping Handle Height AdjustmentRecycling Operation Cutting Height AdjustmentRecycling Cover REMOVAL/INSTALLATION Check Mower Blade Service After First 5 Hours 3.2.1. Change Engine OILAnnually END of Each Season Storage ProcedureBlade Sharpening Adjustments & RepairProblem Probable Cause Corrective Action TroubleshootingUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Cost YOU Money Distorted valve guides Sticking Valves Cap vent open Service Notes Service Notes Steel Deck Walk Behind Mowers Series

R204513E specifications

The Snapper R204513E is a versatile and efficient lawn mower designed to provide homeowners with an exceptional mowing experience. Equipped with advanced features and innovative technology, this mower is perfect for maintaining a well-manicured lawn with minimal effort.

At the heart of the Snapper R204513E is its powerful engine. The mower is powered by a reliable 4-cycle engine, which offers excellent performance and efficiency. This engine provides ample torque to handle various grass types and terrains, ensuring a clean and consistent cut with every pass. Additionally, the mower's self-propelled drive system allows for easy maneuverability, reducing the strain on the user while navigating challenging landscapes.

One of the standout features of the Snapper R204513E is its 21-inch cutting deck. This size strikes the perfect balance between compactness and coverage, making it suitable for both smaller yards and larger lawns. The cutting deck is adjustable, allowing users to choose from multiple cutting heights, ranging from 1 to 4 inches. This customization ensures that homeowners can achieve their desired lawn appearance, whether they prefer a closely trimmed look or a taller, more natural finish.

The mower also boasts a 3-in-1 cutting system. This innovative design allows users to choose between bagging, mulching, or side discharge options. The mulching feature is particularly beneficial for those looking to recycle grass clippings, as it finely chops grass and distributes it back into the lawn as natural fertilizer. The bagging option efficiently collects grass clippings, resulting in a neat and tidy yard.

In terms of user comfort and convenience, the Snapper R204513E includes adjustable ergonomic handles that can be set to various heights to suit the operator’s preference. This ensures a comfortable mowing position and less fatigue during use. Additionally, the mower is equipped with easy-to-access controls, making it simple to operate even for novice users.

Durability is a key characteristic of the Snapper R204513E. It is built with high-quality materials, including a robust steel deck that can withstand the rigors of regular mowing. The design also incorporates reliable components that require minimal maintenance, allowing users to focus more on lawn care and less on upkeep.

Overall, the Snapper R204513E combines power, versatility, and user-friendly features, making it a top choice for homeowners looking to enhance their lawn care routine. With its advanced technologies and thoughtful design, this mower is designed to deliver outstanding performance and reliability for years to come.
Top Page Image Contents