Snapper R204513E important safety instructions Cutting Height Adjustment, Recycling Operation

Page 12

Section 2 - OPERATING INSTRUCTIONS

WARNING

Before attempting any adjustments to the cutting height, STOP the engine, remove the spark plug wire from the spark plug and secure wire away from plug. DO NOT make any adjustments with engine or blade running. Be extremely careful when performing adjustments around engine. Engine is extremely hot and can cause severe burns. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

2.5CUTTING HEIGHT ADJUSTMENT

1.FRONT WHEELS: Reposition the front axle by raising the front wheels off the ground, then pull in the spring loaded bushings until they clear the brackets. Move bushings to the desired height of cut position and release the bushings. See Figure 2.8.

2.REAR WHEELS: Reposition the rear axle by raising the rear wheels off the ground, then pull in the spring loaded bushings until they clear the brackets. Move bushings to the desired height of cut position and release the bushings. Position the rear bushings in to the same notches corresponding with notches for the front wheels to maintain the level of the deck. See Figure 2.8.

NOTE: There are four cutting height adjustment notches on each wheel. The top notch is the lowest cutting height and the lowest notch is the highest.

LOWEST

POSITIONAXLE

BUSHING

FRONT

WHEEL

HIGHEST

POSITION

FIGURE 2.8

2.6 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch

4).

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

2.7RECYCLING COVER (REMOVAL/INSTALLATION)

1.REMOVAL: The recycling cover is secured in place with two knobs. To remove the cover, unscrew the two knobs and lift off the cover. See Figure 2.9.

2.INSTALLATION: When reinstalling the cover, the deck sidewall should fit between the tab and outside of cover. Tighten knobs securely. See Figure 2.10.

SILHOUETTE

OF CUTTING

DECK

 

REMOVE BOTH KNOBS

RECYCLING

BY TURNING

COUNTER-CLOCKWISE

COVER

 

 

FIGURE 2.9

TURN KNOBS

CARRIAGE BOLT & NUT

(USED WITH SIDE

CLOCKWISE

DISCHARGE CHUTE

WHEN

ONLY!)

REINSTALLING

DECK SIDE

 

 

WALL

RECYCLING

COVER

TAB (SHOWS VIEW FROM

UNDERNEATH RECYCLING COVER)

FIGURE 2.10

12

Image 12
Contents Steel Deck Walk Mowers Series Protection for Children Slope OperationPreparation OperationMaintenance and Storage Table of Contents Steel Deck Walk Behind Mowers Lubrication Operational TestDEALER’S Records & Final Check CONSUMER/OPERATOR Product Registration CardPage Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeOptional Power Cords Minimum Gauge for Cord Sets Handle Height Adjustment StoppingCutting Height Adjustment Recycling Cover REMOVAL/INSTALLATIONRecycling Operation Service After First 5 Hours 3.2.1. Change Engine OIL Check Mower BladeStorage Procedure Annually END of Each SeasonAdjustments & Repair Blade SharpeningTroubleshooting Problem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT PartsUSE HRS Season Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Cost YOU Money Distorted valve guides Sticking Valves Cap vent open Service Notes Service Notes Steel Deck Walk Behind Mowers Series

R204513E specifications

The Snapper R204513E is a versatile and efficient lawn mower designed to provide homeowners with an exceptional mowing experience. Equipped with advanced features and innovative technology, this mower is perfect for maintaining a well-manicured lawn with minimal effort.

At the heart of the Snapper R204513E is its powerful engine. The mower is powered by a reliable 4-cycle engine, which offers excellent performance and efficiency. This engine provides ample torque to handle various grass types and terrains, ensuring a clean and consistent cut with every pass. Additionally, the mower's self-propelled drive system allows for easy maneuverability, reducing the strain on the user while navigating challenging landscapes.

One of the standout features of the Snapper R204513E is its 21-inch cutting deck. This size strikes the perfect balance between compactness and coverage, making it suitable for both smaller yards and larger lawns. The cutting deck is adjustable, allowing users to choose from multiple cutting heights, ranging from 1 to 4 inches. This customization ensures that homeowners can achieve their desired lawn appearance, whether they prefer a closely trimmed look or a taller, more natural finish.

The mower also boasts a 3-in-1 cutting system. This innovative design allows users to choose between bagging, mulching, or side discharge options. The mulching feature is particularly beneficial for those looking to recycle grass clippings, as it finely chops grass and distributes it back into the lawn as natural fertilizer. The bagging option efficiently collects grass clippings, resulting in a neat and tidy yard.

In terms of user comfort and convenience, the Snapper R204513E includes adjustable ergonomic handles that can be set to various heights to suit the operator’s preference. This ensures a comfortable mowing position and less fatigue during use. Additionally, the mower is equipped with easy-to-access controls, making it simple to operate even for novice users.

Durability is a key characteristic of the Snapper R204513E. It is built with high-quality materials, including a robust steel deck that can withstand the rigors of regular mowing. The design also incorporates reliable components that require minimal maintenance, allowing users to focus more on lawn care and less on upkeep.

Overall, the Snapper R204513E combines power, versatility, and user-friendly features, making it a top choice for homeowners looking to enhance their lawn care routine. With its advanced technologies and thoughtful design, this mower is designed to deliver outstanding performance and reliability for years to come.