Snapper R1962519B important safety instructions Operation, Maintenance and Storage

Page 3

IMPORTANT SAFETY INSTRUCTIONS

SAFE HANDLING OF GASOLINE

(Continued From Previous Page)

1.DO NOT remove fuel cap or add fuel with the engine running. Allow the engine to cool before refueling.

2.DO NOT refuel the machine indoors.

3.DO NOT store the machine or fuel container inside where there is an open flame, spark or pilot light such as on a water heater or other appliances.

4.DO NOT fill fuel containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place the containers on the ground away from the vehicle before filling.

5.Remove gas-powered equipment from the vehicle or trailer and refuel it on the ground. If this is not possible, then refuel equipment using a portable container, rather than a gasoline dispenser nozzle.

6.DO NOT start gas powered equipment in enclosed vehicles or trailers.

7.Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. DO NOT use a nozzle lock- open device

8.If fuel is spilled on clothing, change clothing immediately.

9.DO NOT overfill a fuel tank. Replace fuel cap and tighten securely.

OPERATION

1.DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area while engine is running.

2.STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.

3.Mow only in daylight or good artificial light.

4.DO NOT operate mower while under the influence of alcohol or drugs.

5.After striking a foreign object or if mower vibrates abnormally, STOP the engine, disconnect and secure spark plug wire. Inspect the mower for any damage and repair the damage before starting.

6.DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or balance.

7.STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.

8.DO NOT mow on wet grass. Always be sure of your footing. Keep a firm hold on the handle and walk, never run. Slipping could cause injury.

9.ALWAYS stay behind handle when engine (motor) is running.

3

OPERATION

(Continued From Previous Column)

10.DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE before leaving the operators position for any reason.

11.Before cleaning, repairing or inspecting make certain engine, blade and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.

12.STOP engine and wait until the blade comes to complete STOP before removing grass bag and/or clearing grass.

13.DO NOT operate mower without the entire grass catcher, discharge guard, rear guard or other safety devices in place and working.

14.DO NOT point discharge at people, passing cars, windows or doors.

15.DO NOT discharge material against a wall or obstruction. Material may ricochet back towards the operator.

16.Slow down before turning.

17.Watch out for traffic when near or crossing roadways.

18.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

19.Only use accessories approved by the manufacturer. See manufacturer’s instructions for proper operation and installation of accessories.

MAINTENANCE AND STORAGE

1.DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep mower and engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Keep all bolts, especially blade bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

5.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, a deadly poison.

6.Service engine and make adjustments only when engine is stopped. Removed spark plug wire from spark plug and secure wire away from spark plug to prevent accidental starting.

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model Number Explanation Steel Deck Walk Mowers SeriesSafe Handling of Gasoline Protection for ChildrenSlope Operation PreparationOperation Maintenance and StorageUsage Statement Table of Contents Nomenclature FamiliarizationPrimer Bulb IntroductionOperating Instructions PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Stopping Handle Height AdjustmentCutting Height Adjustment Recycling Cover REMOVAL/INSTALLATIONRecycling Operation Discharge Deflector Installation Maintenance Service After First 5 Hours 3.2.1. Change Engine OILCheck Mower Blade Storage Procedure Service AnnuallyAdjustments & Repair Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Corrective Action Problem Probable CauseService Performed Each MAINTENANCE/REPLACEMENT PartsUSE HRS Season Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Steel Deck Walk Behind Mowers Series

R1962519B specifications

The Snapper R1962519B is a powerful and efficient lawn mower designed for homeowners who value a well-manicured lawn. With its robust engineering and user-friendly features, this mower stands out in the competitive landscaping equipment market.

One of the key features of the Snapper R1962519B is its 19-inch cutting deck, which allows for a wider cutting path compared to many traditional mowers. This feature enables quicker mowing, making it an ideal choice for those with moderate to larger-sized lawns. The mower is equipped with a 190cc Briggs & Stratton engine, known for its reliability and performance. This engine provides ample power to tackle thick grass and varying terrain types with ease.

The R1962519B utilizes a 3-in-1 cutting system, which means it can mulch, bag, or side discharge grass clippings based on user preference. This versatility not only enhances the mower's efficiency but also allows homeowners to choose the best method for lawn maintenance depending on the season or specific yard conditions.

Another innovative feature of this model is its variable speed self-propel system. This technology allows users to adjust their mowing speed, providing greater control and comfort while mowing. Whether you need to navigate around garden beds or speed through open areas, the Snapper R1962519B adapts to your pace.

Comfort is further enhanced by the adjustable ergonomic handle, which can be customized to suit the user's height and posture. This thoughtful design reduces strain during operation, making it easier to handle and maneuver the mower, particularly on longer mowing sessions.

In terms of construction, the Snapper R1962519B is built with durable materials that withstand rugged outdoor use. The deck's design also promotes optimal airflow, resulting in improved cutting performance and a cleaner finish.

Maintenance is simplified through features such as a quick-change oil system and easy-access air filter. This ensures that users can perform necessary upkeep without needing specialized tools or knowledge.

In summary, the Snapper R1962519B combines practical features, cutting-edge technologies, and thoughtful design to provide an excellent mowing experience. With its powerful engine, versatile cutting options, and user-friendly controls, it is a fantastic choice for anyone looking to maintain a beautiful lawn with minimal effort.
Top Page Image Contents