Snapper EYZ16335BVE important safety instructions Down Eccentric Loosen Shoulder Bolt

Page 20

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns; allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.3.7.MOWER DECK ADJUSTMENT (LEVELNESS) Side-To-Side (33” Decks)

Before making deck leveling adjustments, check the tire pressure. Check tires and add or release air

UP

DOWN

ECCENTRIC

FIGURE 4.9

LOOSEN SHOULDER BOLT

as needed to bring pressure to 12 P.S.I. in front and 12 P.S.I. in rear tires. If tires are properly inflated and mowing is still uneven, adjust side-to-side deck levelness as follows:

1.Place SCRAMBLER on a smooth level surface.

2.Turn engine off and remove key, remove spark plug wire(s) from spark plug(s) and secure wire(s) away from plug(s).

3.Place a piece of angle iron, pipe, or similar object under center of deck at the rear.

4.Remove rear hanger chains and allow center, rear of deck to rest on angle iron.

5.Measure the distance from blade tips to floor. If the measurement is within 1/8” from side-to-side, the deck levelness is satisfactory. If the difference from side-to-side is greater than 1/8”, continue to the next page for adjustment. See Figure 4.8.

 

SINGLE BLADE DECK

SIDE

SIDE

X

X-1/8”

 

ANGLE IRON

FIGURE 4.8

6.Loosen the shoulder bolt that retains the eccentric.

7.Turn eccentric “UP” or “DOWN” as required until blade tips are within 1/8” of the same distance from the floor. See Figure 4.9.

8.Tighten shoulder bolt loosened in Step “f”.

9.Readjust rear hanger chain pivots to align with holes in support brackets.

10.Reconnect hanger chains, remove angle iron, pipe, etc. and recheck side to side level. Adjust either chain as needed to result in blade tips being within 1/8” of the same distance from the floor.

11.Proceed to check front to rear deck pitch.

4.3.8. MOWER DECK ADJUSTMENT (LEVELNESS) Front to Rear Deck Pitch (33” Deck)

With the SCRAMBLER on a smooth, level surface, rotate blade until blade tips are at front and rear of deck. Measure the distance from blade tips to floor. The distance should be the same, or the rear 1/4” lower than the front. If the rear blade tip is higher or is more than 1/4” lower than the front, proceed with adjustment.

1.Remove rear hanger chains.

2.Turn each hanger pivot the same number of rotations on the eye-bolt to raise or lower the rear of the deck. See Figure 4.10.

3.Reinstall rear hanger chains and measure blade tips again.

4.Repeat steps “a” through “c” until proper levelness is obtained.

FRONTREAR

SIDE VIEW OF DECK

ROTATE HANGER

PIVOT UP TO RAISE

DECK OR DOWN TO

LOWER DECK

REAR LIFT ARM

FIGURE 4.10

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents European Scrambler Hydro Drive Series Model Number ExplanationProtection for Children Protection Against Tipovers PreparationSafe Handling of Gasoline OperationMaintenance Table of Contents Nomenclature FamiliarizationIntroduction Familiarization Decals / Symbols Operating Instructions PRE-START Check ListStarting & Operation Engine Electric Start Mower Blade StoppingEngine Parking BrakeCutting Height Adjustment Engine Must not Start ifEngine should Start if Engine Must Begin to Stop ifMaintenance Service After First 5 HoursChange Engine OIL Check Mower BladeChecking Mower Belt Tension Check EngineEngine Cooling System Engine Oil Oil Filter Fuel Filter Air FilterMower Components Underside View of 33 DeckParking Brake Pivot Bushings Scrambler Lubrication 1. Front Wheel BearingsFront Caster Wheel Pivot Shaft Service Annually Storage OUT of SeasonAdjustments & Repair Do not attempt any adjustments, maintenanceService or repairs with the engine running. Stop Neutral PositionEngine Adjustments & Repair Mower Drive Belt AdjustmentBelt Replacement Belt ReplacementsBlade Brake Adjustment Adjusting Mower BladeDown Eccentric Loosen Shoulder Bolt Wheel Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear LimitsMower Deck Timing ROD Blade SharpeningMower Blade Replacement 4.4.3. Blade Replacement Battery Battery RemovalBattery Installation 1. Slide battery into battery cradle Battery ServiceBattery Testing NEW Battery Preparation 1. Remove battery from cartonCorrective Action Problem Probable CauseTrouble Shooting on Next Problem Probable Cause Corrective Action Excessive VibrationService Performed Each MAINTENANCE/REPLACEMENT Parts100 USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance European Scrambler Hydro Drive Series

EYZ16335BVE specifications

The Snapper EYZ16335BVE is a versatile and powerful lawn mower designed for both residential and commercial use. Known for its exceptional cutting ability and user-friendly features, this model stands out in the competitive outdoor power equipment market.

At the heart of the Snapper EYZ16335BVE is a robust 163cc engine that delivers reliable power and efficient operation. The engine is designed to provide ample torque, ensuring that the mower can handle tough turf as well as fine lawns with ease. The self-propelled feature enhances maneuverability, allowing users to navigate through various terrains without putting extra strain on themselves.

One of the standout characteristics of the EYZ16335BVE is its 21-inch steel mowing deck, which provides superior durability and a wide cutting path for faster mowing. This model offers adjustable cutting heights, allowing users to choose between different grass lengths ranging from 1 to 4 inches. The ability to customize the cut makes it suitable for diverse grass types and can contribute to healthier lawn growth.

The Snapper EYZ16335BVE is equipped with a reliable 3-in-1 cutting system, offering options for mulching, bagging, or side discharge. This versatility allows users to manage lawn clippings efficiently based on their preferences or lawn care requirements. The mulching feature returns finely chopped clippings to the lawn, providing natural fertilization.

Ergonomically designed, this lawn mower includes a padded handle for comfort during operation. Its lightweight construction ensures that it is easy to maneuver and transport, reducing user fatigue during extended mowing sessions. The foldable handle is an additional convenience, making storage simple and efficient.

In terms of maintenance, the Snapper EYZ16335BVE is designed for ease of service. Accessible air filters and an easy-start engine design simplify routine maintenance tasks, ensuring that the mower operates at peak performance year-round.

Overall, the Snapper EYZ16335BVE embodies innovation and practicality, making it a reliable choice for homeowners and landscaping professionals. With its exceptional features, solid construction, and advanced technologies, it provides an efficient mowing solution that meets the demands of various lawn care needs. Whether tackling vast lawns or navigating smaller residential yards, the Snapper EYZ16335BVE consistently delivers results that exceed expectations.
Top Page Image Contents