Snapper ESZT18336BVE Check Engine, Mower Components, Lubrication, Underside View of 33 Deck

Page 15

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3SERVICE - EVERY 25 OPERATING HOURS (Continued From Previous Page)

3.3.1. CHECK ENGINE

4. Air Filter

2.Refer to engine owner's manual for cleaning and service instructions. Remove and clean engine air pre-cleaner. Remove and replace engine air cleaner. See Figure 3.5. Install pre-cleaner and air cleaner per engine owner’s manual.

AIR PRE-

CLEANER

AIR CLEANER

FIGURE 3.5

3.Reinstall air cleaner cover. Insert tabs located at the bottom of the cover into corresponding slots in engine cover. Position cover and engage latch over cover and rotate and push down to lock.

3.3.2.MOWER COMPONENTS

1. Blade Brake

Check blade stop time. Blades must stop rotating in 5 seconds or less after blades have been turned off. Refer to Section “BLADE BRAKE ADJUSTMENT”.

2. Mower Drive Belt

Check belt for proper tension. No adjustment required. Replace belt as needed.

3. Mower Blade

Check blade for sharpness, wear, damage, and torque. Refer to Section “MOWER BLADE REPLACEMENT”.

4. Mower Deck Levelness

Check mower deck for proper levelness. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT – LEVELNESS”.

5.Cleaning Mower Deck

a.Close vent on fuel cap and make sure cap is tight. See Figure 2.2.

b.Remove key from ignition switch. Engage parking brake.

c.Remove spark plug wire(s) and secure away from spark plug(s).

d.Raise cutting deck to highest setting.

e.With a floor jack, carefully raise up front of machine to gain easier access to under deck. Block machine securely.

WARNING

Lifting or lowering the machine onto or down from blocks manually can cause severe injury. Always use a floor jack when raising machine.

f.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

g.Clean top of deck, removing all grass clippings and debris.

3.3.3. LUBRICATION

1.Mower Blade Spindle

a. Lubricate spindle bearings with three shots of general purpose grease from grease gun. See Figure 3.6.

UNDERSIDE VIEW OF 33” DECK

LUBRICATE

SPINDLE BEARINGS

FIGURE 3.6

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model Number Explanation ScramblerFrom Previous Column Protection for ChildrenProtection Against Tipovers PreparationOperation Safe Handling of GasolineTowing MaintenanceTable of Contents Nomenclature IntroductionMotion Control Levers Cutting Deck Adjustment Handle Forward of Operator SeatEngine Speed & Choke Control Right Control Panel Parking Brake Next to Left Control Panel Applies park brakePRE-START Check List Engine Operation 2.2.1. Starting EngineStopping Engine Reverse Motion Motion ControlGetting Ready Forward MotionStopping Motion Conventional TurningLeft turn shown right turn opposite ZERO-TURNINGMower Blade Disengagement Mower Operation Cutting Height AdjustmentMower Blade Engagement Mowing OperationsEngine Must not Start if Engine should Start ifEngine Must Begin to Stop if Single Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeEngine Oil Oil Filter Air Filter Service Every 25 Operating HoursChecking Mower Belt Tension Engine Engine Cooling SystemUnderside View of 33 Deck Check EngineMower Components LubricationMotion Control Pivot Bushings Front Wheel BearingsFront Caster Wheel Pivot Shaft Parking Brake Pivot BushingsStorage OUT of Season Service AnnuallyMotion Control Adjustments Neutral AdjustmentsTracking Adjustments Deck Engine Adjustments & RepairMower Drive Belt Adjustment Belt ReplacementIdler ARM and Belt Guide Detail Blade Brake AdjustmentBelt Replacements From Previous+ 1/16 From Previous Page Checking the 33 Deck BladeDeck Shown Front or Rear View of DeckMower Deck Timing ROD Front to Rear Deck Pitch 38 DecksWheel Brake Adjustment Mower Blade Replacement 4.5.1. Blade Wear LimitsBlade Sharpening Battery Service Blade Replacement ChartMower Blade Replacement 4.5.3. Blade Replacement Battery Battery RemovalNEW Battery Preparation 1. Remove battery from carton Battery TestingProblem Probable Cause Trouble Shooting on NextCorrective Action Excessive Vibration Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Decal Identification European Noise Control Decal Disclaimer of Warranty Year Limited WarrantyPage Page Page Scrambler ZERO-TURN Hydro Drive European Model Series

ESZT18336BVE specifications

The Snapper ESZT18336BVE is a cutting-edge electric lawn mower designed for homeowners seeking efficiency, power, and ease of use. This innovative model integrates advanced technologies and features that enhance the mowing experience while ensuring a high-quality finish on various lawn types.

One of the standout features of the Snapper ESZT18336BVE is its powerful 36V lithium-ion battery system. This robust power source provides extended run time, allowing users to cover larger areas without the hassle of cords or frequent recharging. The battery is designed for quick charging, ensuring that the mower is ready when you are. Its energy-efficient operation not only reduces electricity costs but also contributes to a cleaner environment by emitting no harmful emissions.

The ESZT18336BVE boasts a versatile 18-inch cutting deck, ideal for small to medium-sized lawns. This size strikes a perfect balance between maneuverability and efficiency, enabling users to navigate around obstacles and corners with ease. The adjustable cutting height feature provides six different settings, ranging from 1 to 3.5 inches, allowing users to achieve their desired lawn height and adapt to varying grass types and seasonal growth.

Ergonomics play a significant role in the design of the Snapper ESZT18336BVE. The mower is equipped with a comfortable handle that can be adjusted to different heights, catering to users of varying statures while reducing strain during operation. The lightweight design further enhances ergonomics, making it easy to lift and transport.

Safety is paramount in the design of the Snapper ESZT18336BVE, featuring a reliable safety key that prevents accidental starting. Additionally, the mower integrates a blade brake system that stops the blade quickly when the user releases the control handles, providing peace of mind during operation.

The Snapper ESZT18336BVE also incorporates innovative mowing technologies, including a 3-in-1 mulching system that allows users to mulch, bag, or discharge grass clippings. This flexibility enables the efficient disposal of lawn waste and contributes to a healthier lawn by returning nutrients back into the soil.

In summary, the Snapper ESZT18336BVE combines power, convenience, and user-centric design. Its advanced battery technology, adjustable cutting deck, ergonomic features, and smart safety mechanisms make it an excellent choice for homeowners who prioritize performance and sustainability in their lawn care routine.
Top Page Image Contents